LumberJocks

Router Table

  • Advertise with us
Project by Jon Brandt posted 01-23-2011 03:24 AM 2501 views 5 times favorited 11 comments Add to Favorites Watch

I think this is really nice. Build out of maple and the knobs are elk antler.





11 comments so far

View Dan Hux's profile

Dan Hux

576 posts in 2128 days


#1 posted 01-23-2011 03:39 AM

very nice looking router table, are you sure you wanna use it for woodworking? well done

-- Dan Hux,,,,Raleigh, NC http://whitdaniel.com

View jerrells's profile

jerrells

868 posts in 1638 days


#2 posted 01-23-2011 04:22 AM

One nice looking router table. I can tell that the projects coming off that will be equally as good.

-- Just learning the craft my Lord and Savior Jesus Christ practiced.

View Bob, Oregon's profile

Bob, Oregon

90 posts in 2145 days


#3 posted 01-23-2011 04:36 AM

Beautiful work! I can’t wait to see the projects you produce on it!

-- 73, Bob

View BobAtl's profile

BobAtl

49 posts in 1447 days


#4 posted 01-23-2011 05:44 AM

GREAT looking router table! Can you provide any details on the fence you built and show with the table? I’m planning a combination fixed miter saw stand and router table. I want the router table fence to serve double duty as a fence for the miter saw on that end of the station/stand. I’m planning on a 48” x 32” table on each side of my miter saw, with one including the router table and the other doing double duty as an assembly table. Both will need a fence I can adjust in T-tracks or remove as needed.

Bob

-- Bob, Atlanta

View lanwater's profile

lanwater

3100 posts in 1688 days


#5 posted 01-23-2011 05:47 AM

Good looking table.

-- Abbas, Castro Valley, CA

View woodworkerscott's profile

woodworkerscott

362 posts in 1568 days


#6 posted 01-23-2011 07:33 AM

Now THAT”S a router table. Sweet.
Only suggestion would be to leave an open router compartment for cooling purposes. Nice work.

-- " 'woodworker'.....it's a good word, an honest word." - Sam Maloof

View jm64's profile

jm64

36 posts in 1436 days


#7 posted 01-23-2011 11:00 PM

Well done! That’s a really nice table.

-- Joe, Cumming, GA

View jbell2355's profile

jbell2355

21 posts in 1562 days


#8 posted 01-24-2011 04:36 PM

You’re right, it’s great!

-- She was only a rancher's daughter, but all of the horsemen knew her.

View Martyroc's profile

Martyroc

2708 posts in 1060 days


#9 posted 05-02-2012 01:56 AM

That’s a serious router table, great job.

-- Martin ....always count the number of fingers you have before, and after using the saw.

View timbertailor's profile

timbertailor

1100 posts in 178 days


#10 posted 07-02-2014 11:48 PM

Are you going to leave the wood bare or do you have plans to stain it\protect it?

I really like the attention to detail in your table.

Thanks for sharing.

-- Brad, Texas, https://www.youtube.com/user/tonkatoytruck/feed

View widdle's profile

widdle

1474 posts in 1752 days


#11 posted 07-02-2014 11:49 PM

nice..Clean set up..

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase