LumberJocks

My new Dust Collector Separator and Cart

  • Advertise with us
Project by Acts65Woodworks posted 07-05-2017 08:17 AM 2190 views 2 times favorited 5 comments Add to Favorites Watch

I hate dust. My shop is also my garage and dust gets on everything. I started out using a shop vac but it was really noisy and not that effective so I gave up on that. A 2hp dust collector seemed too expensive for me as a hobby woodworker on a budget and it would also take up valuable floor space as well (we still try to park one car in the garage), so for a while I hadn’t been using any dust collection aside from a broom and leaf blower.

A little while ago I picked up a Harbor Freight 1 hp portable dust collector on Craigslist for $30 but it clogged up easily when I used it with my planer and the filter was a 30 micron bag that let a bunch of fine dust back out when I used it with my table saw. It definitely needed some work, specifically a better filter and some type of separator. My goal was to keep it cheap with a small footprint, but effective and I wasn’t sure how, so I just stuck with my broom and blower.

I finally got around to working on it recently and am pretty happy with the result. I made a cyclone/baffle out of an Arrowhead 5 gallon water bottle that someone threw out. I cut off the top of the bottle and flipped it around and secured it in the bottom part of the bottle (see picture) and attached a 4” angled dust port on the side. Then I cut a hole on top so I could rest the dust collector on top and then cut a hole in the lid of the Home Depot bucket and put it all on top of that. I bought a 3 micron filter bag on Amazon (I couldn’t find a lower micron bag that would fit the portable dust collector). Then I made a stand out of scrap MDF and plywood and put it on casters and put a piece of granite on the bottom so the cart wouldn’t tip over as easily since the dust collector motor was pretty high in the setup.

The dust collector works great, doesn’t get clogged with planer shavings, has a pretty small footprint, also functions as a work surface, is much quieter than a shop vac, and cost me about $70 for everything. I am really happy with how it all turned out and I wish I had finished this earlier.

-- Steven, California, https://www.etsy.com/shop/Acts65Woodworks, https://www.instagram.com/acts65_woodworks/





5 comments so far

View Kelster58's profile

Kelster58

298 posts in 290 days


#1 posted 07-05-2017 10:23 AM

Pretty cool…...Great job with the engineering and build!

-- K. Stone “Tell me and I forget, teach me and I may remember, involve me and I learn.” ― Benjamin Franklin

View Mainiac Matt 's profile

Mainiac Matt

7199 posts in 2078 days


#2 posted 07-05-2017 02:04 PM

You did a very novel design on this one…. You may be the trend setter for a new type of separator.

How did you float the baffle piece inside the water bottle?

-- Pine is fine, but Oak's no joke!

View Daiku's profile

Daiku

232 posts in 2658 days


#3 posted 07-05-2017 02:47 PM

That’s friggin ingenious! I think I have an old 5 gal. water container somewhere, I’ll have to give that a try.

Thanks for posting,

-- Cal Noguchi - EZdado.com

View helluvawreck's profile (online now)

helluvawreck

27707 posts in 2617 days


#4 posted 07-05-2017 03:16 PM

You did a nice job on this dust system.

helluvawreck aka Charles
http://woodworkingexpo.wordpress.com

-- If a man does not keep pace with his companions, perhaps it is because he hears a different drummer. Let him step to the music which he hears, however measured or far away. Henry David Thoreau

View Acts65Woodworks's profile

Acts65Woodworks

20 posts in 292 days


#5 posted 07-05-2017 05:03 PM

Mainiac Matt – I am really happy with how it turned out. Most of the setups I’ve seen have a bucket next to the dust collector and that makes the foot print a lot bigger than this one, since it stacks. To get the baffle piece to “float” inside the water bottle, I cut it in the shape of a light bulb and I screwed the part that stuck out to the side of the bottle so the rest would “float”. Hope that makes sense, if not, I can take an extra picture or something.

-- Steven, California, https://www.etsy.com/shop/Acts65Woodworks, https://www.instagram.com/acts65_woodworks/

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com