LumberJocks

More bread boards

  • Advertise with us
Project by mtnwild posted 02-17-2010 01:03 AM 2069 views 11 times favorited 10 comments Add to Favorites Watch

Or hot dish holder or table center piece holder or what ever you might come up with. Fairly versatile and people love them.
Was given some nice scrap end pieces of oak and mahogany and went to work. These are just a few. Trying to get a stock pile going.
Not too exciting but a great slow time in the shop project. A great training project for the beginners. I’m learning a lot…............
Thanks for looking…............................

-- mtnwild (Jack), It's not what you see, it's how you see it.





10 comments so far

View SuperDave0002's profile

SuperDave0002

136 posts in 1917 days


#1 posted 02-17-2010 01:08 AM

that really looks sweet, nice job

-- David South FLorida http://ahunkahunkaburninlove.blogspot.com/

View degoose's profile

degoose

7038 posts in 2041 days


#2 posted 02-17-2010 03:00 AM

Hey there Jack… nice TREVIT.

-- Drink twice... and don't bother to cut... @ lazylarrywoodworks.com.au For lovers of all things timber...

View Jonathan's profile

Jonathan

2605 posts in 1737 days


#3 posted 02-17-2010 03:10 AM

I like that. Looks like a good way to practice using my dado set.

Nice use of scrap too.

-- Jonathan, Denver, CO "Constructive criticism is welcome and valued as it gives me new perspectives and helps me to advance as a woodworker."

View Rj's profile

Rj

1047 posts in 2317 days


#4 posted 02-17-2010 03:49 AM

Jonathan I’m with you ! Nice job Jack

-- Rj's Woodworks,San Jose & Weed Ca,

View Ken90712's profile

Ken90712

15082 posts in 1875 days


#5 posted 02-17-2010 11:46 AM

Very Nice! You using a kerf kig to make thses? Would love to here more info and demension info on this! great job!

-- Ken, "Everyday above ground is a good day!"

View mtnwild's profile

mtnwild

3474 posts in 2213 days


#6 posted 02-17-2010 04:44 PM

Thanks everyone!
Ken, I have a blog on my home page on basically how these are made. I glue different woods together to get the different woods to all align, then dado, then cut to strips. I usually have more pieces than I need after the cuts. That’s a good thing in case any break, or for the variations later if you have enough pieces left over.
Size I vary according to my wood selection. I don’t have a lot. They average about 9”x !2”. This would be a good use for the ” Fibonacci gauges”.

-- mtnwild (Jack), It's not what you see, it's how you see it.

View D1st's profile

D1st

289 posts in 1726 days


#7 posted 02-17-2010 06:02 PM

Could a box joint jig be used instead of a dado blade? Just curious as i dont have a dado yet and dont want to run the pieces thru 100x

-- http://www.furstwoodworks.com/

View mtnwild's profile

mtnwild

3474 posts in 2213 days


#8 posted 02-17-2010 07:34 PM

Sure, as long as each dado is the same as the next. They have to be straight to fit the best. Square is key.

-- mtnwild (Jack), It's not what you see, it's how you see it.

View studie's profile

studie

618 posts in 1833 days


#9 posted 02-18-2010 07:44 AM

Very cool stuff! Come and get some IPE scraps from me to make more of these as IPE wont burn?

-- $tudie

View mcoyfrog's profile (online now)

mcoyfrog

3271 posts in 2280 days


#10 posted 02-22-2010 11:07 PM

great trivet

-- Wood and Glass they kick (well you know) Have a great day - Dug

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase