LumberJocks
DAILY DEALS Precision Taper Jig  |  Makita Makita Recon LCT203W 10.8 Volt Lithium Ion Impact Driver 2 Pc Kit

Myrtle Footed Cup

Project by scrappy posted 122 days ago 340 views 0 times favorited 9 comments Add to Favorites Watch

Here is my first Footed Cup. Just had to go get a turning block from Rockler today. 4×4 x 4 inch block of Myrtle.
Could not tell a lot about the wood when I bought it. It was covered with wax. When I was turning it all the great grain showed up, I REALLY like the RAYS going across it.

Decided that with it being square, it would be a deep cup. So added the foot to the design. Tapered the outside and cut the inside straight in. The wall at the top ring is only 3/32 thick. Got a little thinner then I was shooting for. At the second ring is 5/32 thick. Kept most of the starting size. Finished size is 3 3/4 tall and 3 3/4 diameter.

I am realy enjoying turning stuff. The only poblem, is finding wood without haveing to glue it up. This is basically the first piece of wood that I have purchased that wasn’t out of a “cut off bin” or some one elses scrap given to me. Or my favorite, Pallet wood! Everything at least 3 inch thick I have found is all cracked up.

Looking forward to turning more every day. Will have to make up a segmented piece and see how that turns out.

Thank you for looking. Please leave all comments and sugestions.

Allmost forgot. Finished by sanding to 300 grit, raising grain with mineral oil and sanding again. Re oiling after all done. Turned into a nice satin finish, slick and smooth. (so slick when wet I dropped it and put a tiny chip in the rim)

Thanks again for looking.

Scrappy

-- Scrap Wood's the best...the projects are smaller, and so is the mess!


9 comments so far

View Don K.'s profile

Don K.

1095 posts in 223 days


posted 122 days ago

VERY nice…beautiful wood…well done !!!!!

-- Don S.E. OK

View a1Jim's profile

a1Jim

16978 posts in 474 days


posted 122 days ago

super job well done

-- Jim from Heirloom Woodshop Southern Oregon

View TopamaxSurvivor's profile

TopamaxSurvivor

3044 posts in 573 days


posted 122 days ago

Looks good from here Scrappy!! Now you can drink a cold one :-))

-- Debt is nothing more than the 21st Century's form of slavery.

View Durnik150's profile

Durnik150

536 posts in 219 days


posted 122 days ago

Great job! The rays in that cup really grab your eye. You should be very proud of this piece.

-- Behind the Bark is a lot of Heartwood----Charles, Centennial, CO

View Bill Akins's profile

Bill Akins

236 posts in 595 days


posted 121 days ago

Beautiful cup. Nice turning.

-- Bill from Lithia Springs, GA I love the smell of sawdust in the morning.

View Innovator's profile

Innovator

3125 posts in 310 days


posted 121 days ago

Nice looking cup, good job.

-- Whether You Think You Can or You Think You Can't, YOU ARE RIGHT!!!

View LesB's profile

LesB

551 posts in 340 days


posted 121 days ago

Nice work.
I saw your other Myrtle wood piece too. It is great wood to turn and work with. I have used a lot of it. In actuality it is California Bay Laurel and it grows primarily along the west coast from central California to Northern Oregon. My experience is that the wood that grows in Oregon seems to have more color than that from California. In the past for marketing purposes shops in Oregon spread the untruth that it only grew in Oregon and the Holy Land. The Myrtle from the Holy Land is another species entirely.
If you don’t seal the wood it will darken considerably over time. I made a tansu cabinet several years ago that I finish with several coats of water based poly only and it is holding its lighter color. Wood I have just oiled and waxed darkened with in a few months. If you check my project postings you will find the cabinet and a clock (in the same picture) made from the same milled log and see the difference. The clock was oiled/waxed.

By the way, the leaves can be used as a substitute for “bay laurel” seasoning (from Greece) in spaghetti sauce, etc. and they are a good insect repellant in the kitchen cupboards.

-- Les B, Oregon

View scrappy's profile

scrappy

1641 posts in 327 days


posted 121 days ago

Thanks for all the great comments everyone.

LesB, Thanks for the info. All I did was oil these 2 pieces so I they should darken nicely with time. Did not know Myrtle (California Bay Laurel) did that. Thanks again.

Thanks again everyone.

Scrappy

-- Scrap Wood's the best...the projects are smaller, and so is the mess!

View blockhead's profile

blockhead

295 posts in 205 days


posted 118 days ago

Great job Scrappy! You are getting really good with the turning. The wood is beautiful and I love the cup design!

-- Brad, Oregon- Wood, it's what's for dinner.

You must be signed in to post the comments.

  • View all advertisers
  • Advertise with us

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase