LumberJocks

X-Men Bunk Bed #3: Assembling the Circle-X Panels

  • Advertise with us
Blog entry by Patrick Jaromin posted 05-03-2012 11:36 AM 1293 reads 0 times favorited 1 comment Add to Favorites Watch
« Part 2: The Headboard and Footboard Part I, Making Xs Part 3 of X-Men Bunk Bed series Part 4: Test Assembly and Finishing the Ends »

Fits and Starts

The last couple weeks have been crowded with both personal and professional activities. I’ve had to work in found time, an hour here, an hour there. My next task was to fit the upper and lower bouts of the “X”s with their panels.

Finishing the Wedges

The pie wedges are cut from 1/2” cherry plywood, stained to match the poplar hardwood used elsewhere. Though it seems a shame to stain cherry, the cheaper plywood readily available to me was pretty poor stuff and, well, I wasn’t 100% certain I wasn’t going to use cherry for the rest of it when I got it…so, that’s where we are. In any case, I figured it’d be far easier to stain and finish the panels before they were glued into place in their MDF frames. After a bit of experimentation, I settled on a two part process of penetrating stain topped with a gel stain. Then I went to the big box and wound up buying a single can of Minwax<sup>®</sup> Polyshades and using that instead. It does a very nice job of obscuring the poplar and hiding the green, though my attempts to brush it on with a foam brush left me less than satisfied. I wound up wiping it on instead, which produced far superior results. Definitely a time-saver, and I think they came out great, no?


Staining the plywood wedges

Notching for Entry

I must admit to being a bit concerned about notching out the top for the entry. I considered leaving the top as-is since I’m fairly certain it wouldn’t be at all difficult to climb over the end. However, it simply didn’t look right that way and it would probably get old having to slide over the arc. In any case, I dry fit the assembly on top of the full-size drawing and laid out the notch.

To my amazement it came out essentially dead-on. Sometimes you get lucky!


Laying out the top bunk entrance


Top corner cut out


Trim for knock out finished and dry fit

Assembling the Panels

With relatively stable MDF frames and plywood panels, it seemed safe to glue the panels in place instead of trying to float them. They’ll also provide extra strength to the relatively weak MDF structure. The glue-up went smoothly. The posts are here to help align all the parts; I plan to mortise and drill for the rail assembly and stain them before gluing the panels permanently between them. Now I’ve just got to figure out exactly how I’m going to join the rails. Although I’ve purchased some metal knock-down bed-rail hangers, I have concerns both about the possibility of a child on the lower bunk pushing the top rail up and out, and the holding power of screws holding in the end grain. I’m leaning right now toward using these plus a single long bolt through the post into a barrel nut in the bed rail to keep it together. The problem with that is I absolutely loathe barrel nuts – I can never get them to line up just right. I’ll keep mulling this over….any ideas?


Center panel glued up and set aside with posts for safe-keeping

[Originally posted at http://tenonandspline.com/blog/archives/710]

-- Patrick, Chicago, IL http://www.TenonAndSpline.com/blog



1 comment so far

View derosa's profile

derosa

1557 posts in 1553 days


#1 posted 05-03-2012 02:46 PM

Good looking Xs, I don’t know how I missed the first two posts but this is a cool design.

-- --Rev. Russ in NY-- A posse ad esse

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase