LumberJocks

phlyers's Forum Topics

  • Advertise with us
View phlyers's:homeworkshopprojects (0)blog (0)reviews (0)forum topics (34)buddies (0)favorites (0)activity logWatch
08-26-2013 10:46 AM

TS extension wing - 6 replies

Do people typically make a removable router fence if they’re going to incorporate the router on the TS extension wing or is it easier to just incorporate it in the TS fence? I guess what i’m saying is I want to add a TS wing and get a router lift but also need the fence to be removable due to the face that I sometimes use my TS rip ...

08-23-2013 02:42 AM

Spindle sander - 4 replies

I’ve got my eye on this one. 1/2 hp motor…I can assume that’s not for real heavy duty work? http://philadelphia.craigslist.org/tls/3962695663.html

08-18-2013 09:11 PM

taper jig - 11 replies

I just made a jig like this http://www.rockler.com/product.cfm?page=2076&site=ROCKLER&TabSelect=Reviewsout of stuff I had laying around. Question is this…Does the length of the jig matter greatly depending on the work piece you have to cut on a taper? In other words if my jig is 24” long I’m really limited to cutting ...

08-13-2013 02:28 AM

New "toy" - 4 replies

Ya either hate Craigslist or you love it and today i’m loving it. Got this guy for $150 brand new in box. It’s a 1998 model. First use was some hickory to make my runners for the table saw cross cut sled. So psyched!!!

08-12-2013 03:10 AM

Older 4 1/2" Craftsman jointer - 3 replies

I recently acquired one and have a dumb question. I’m probably overlooking something but here goes. One half of the table is stationary (can’t be raised/lowered) while the other half can be raised or lowered depending on how much you need to take off each pass via a small T-handle. When I say “half” I mean it’s T...

08-07-2013 12:44 PM

securing my table saw - 9 replies

The best place for my table saw in my shop of course is the place where the floor is not level at all. Right now I have wood shims under it to make it level with my work table (my work table is basically built around the table saw) but eventually overtime the vibration from the saw would make the saw “walk” so myI thought would be t...

08-06-2013 01:25 AM

Sanding/hiding a dowel - 5 replies

Hey guys I had to use a 3/8” poplar dowel to plug a hole in a project I’m working on and after cutting it flush and sanding it really smooth it shows right through the paint. It feels rough when you run your finger across it. Did I not sand it smooth enough? Or was it maybe the fact that I didn’t use fine enough paper? I use...

07-31-2013 02:02 AM

Fastening the newel post - 4 replies

Our new railing will require the newel post to be mounted on top of the first stair tread (off to the side as a volute will be used) Hopefully you can picture this. This particular location is above the basement so I have full access to it below the floor. Would it make sense to recess the post into the tread cavity and lag bolt it from the b...

07-28-2013 01:27 AM

ZCI question - 5 replies

Just a pointless question here but when I ran my blade up to make the slot on my ZCI the kerf of the blade still rides against the sides of the opening. I figured it would wear in over time but still doing this and it’s really annoying to hear it riding on the sides. Any fix for this? I figured I could try to file the sides a little but...

07-24-2013 02:53 AM

FS: Incra T-Track Plus 18" - 2 replies

This is brand new never used. I was going to use it on my V120 mitre gauge but used something else instead. This needs to go to good use as I don’t want it sitting around. How about $15 shipped. I only accept PayPal. PM me if interested.

07-24-2013 02:32 AM

Name that jointer - 5 replies

I acquired this (for free!!) but there aren’t any tags on the jointer itself. It does have a Westinghouse motor. Does anyone know what brand this is an approx age?

07-15-2013 10:43 AM

Blade alignment - 18 replies

Hopefully someone can help me out on this. I aligned my TS blade with the mitre slot with the blade ALMOST all the way up with my calipers and a Mag-Dro and the blade at a perfect 90 degree. I got it within .006” but for some reason it goes out of wack again when I lower the blade. Obviously I will need to raise and lower the blade a lo...

07-10-2013 07:00 PM

Belt size - 1 reply

Hey guys. Anyone happen to know the correct belt size for my craftsman 113.29920 TS? They’re 1/2” wide but unsure of the length. I have a feeling the current ones I have now are stretched so I can’t really compare. Downloaded the manual online but it does not tell the size of it.

07-10-2013 08:46 AM

Vintage Craftsman - 1 reply

Hey guys. New here and received some welcomes so thank you for the welcome! I have an older craftsman TS. It’s model number 113.29920 if this helps. Hopefully someone is familiar with this one so here’s my question. To align the blade to the mitre slot do I loosen the table bolts and shift into position or does the trunion get a...

« prev 1 2
34 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase