Carl Webster's Forum Topics

  • Advertise with us
View Carl Webster's:homeworkshopprojects (0)blog (0)reviews (0)forum topics (8)buddies (1)favorites (0)activity logWatch
05-06-2012 05:33 PM

Recommended nail guns for fence panels and siding (1 3/4" Max Length nails) - 11 replies

Anyone out there have any recommendations for a pneumatic nail gun for constructing fence panels and nailing siding. I have several Porter Cable nail guns (framing and finish nailers) which have given good service. Porter Cable has a coil magazine roofing nail gun which I assume can be used for fencing and siding. I’m just looking for some...

11-02-2011 11:06 PM

Table Saw "Blade Raising Mechanism" Jamed - 13 replies

I have an older model Craftsman table saw built by Emerson Electric. The model # is 113.298031. The casting that houses the blade arbor rotates around a shaft on a fixed casting as the blade is raised or lowered by a rack and pinion mechanism. The casting housing the blade arbor is “frozen” on the shaft and will not allow the blade t...

10-06-2011 05:55 PM

Installing Can Lights in Kitchen Ceiling - 8 replies

I have a project to install several “can” lights in a kitchen ceiling. I am using a 6 inch + hole saw to cut the holes. The ceiling is sheeted with 1×4 tongue and grove pine and covered with ceiling tile. The hole saw is too large to use a standard 1/2 inch drill to cut the holes for the can lights. What type of drill should I u...

05-12-2011 04:05 AM

Review of Multitool Woodworking Tools - 29 replies

I am in the market for “one” of the brands of multitool woodworking tools. I have looked a Dremels, Rockwells, Porter Cables and have read the reviews on the Internet. Apparently the Fein Multimaster is rated very high, but is also the most expensive. Rockwells Sonicrafter “looks like a nice tool but the reviews said that they ...

04-06-2011 10:29 PM

Freeman Nail Guns - 12 replies

Does anyone have any experience with Freeman Nail guns? I’m interested in a 23 guage pinner nail gun and am wondering if the Freeman Guns are of good quality. My other nail guns are Porter Cable, which have given good service.

03-09-2011 04:26 PM

Hole Saw for easy installation of recessed can lights - 10 replies

I am in the process of a remodeling project that involves the installation of several recessed (in the ceiling) can lights. The lights are listed as 6 inch lights, but the size of the hole you have to cut to install the light can is approximately 6 and 1/4 inches. Are hole cutting saws available in this size? Most of the hardware stores I have v...

02-03-2011 06:40 PM

Bolt size for Attaching Fence to Delta Bandsaw - 5 replies

I have a 14” Delta bandsaw model # 28-275. I need to know the bolt size and threads/inch that holds the fence guides to the table. The bolt size appears to be 1/4 inch but I don’t know if the threads are course or fine. I guess my only choice is to buy 4 bolts of each (course/fine).Thanks.

10-30-2010 02:19 AM

Rip Fence for Delta 14" Band Saw - 3 replies

I have recently purchased an older Delta band saw (American Made) and would like to add a rip fence. I have located two sources, on line, for fences that will fit my saw. The first at Mikes Tools is a Delta brand with a “clamping” design clamping to a steel angle on the front and back of the band saw table. The second design is a Kre...

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics