LumberJocks

jap's Favorites

  • Advertise with us
View apprentice's profile

Rosewood fretsaw

07-15-2012 03:52 PM by apprentice | 16 comments »

I have just completed this copy of a Victoria fretsaw, I made it in a day and a half using minimal tooling other than a bandsaw and a pillar drill press.The main frame is made from Honduran Rosewood with an Ebony brace bar handle and adjuster knob. The metal blade holders are made from stock silver steel 10.00mm and made is such a way that they are one piece for durability, there is a 12.00mm slot cut into the middle and a 6.00mm hole drilled at the bottom of this slot to allow the two hal...

Read this entry »


View patron's profile

mexican tile 'cut and switch' #1: simple stacked cuts - tutorial

11-10-2012 12:25 AM by patron | 34 comments »

this is how this box tiles were done the box is here and as a received gift here started with 4 different woodsall the same size and stacked them 4 colors in each pile and made a holder to run them random freehand thru the bandsaw with a pressure ‘thumb’ on it after cutting thru them curvy to the same corneri switched and glued all the 4 different colors togetherand cleaned them lightly on the disk sanderso they would be flat for the sled with a square stopand...

Read this entry »


View CalgaryGeoff's profile

Bowl from a board

11-08-2012 10:00 PM by CalgaryGeoff | 9 comments »

Hi, I’ve seen a few members are interested in the bowl from a board build process. I will share the steps I used to make a dove tail segmented bowl from a board. The only tragedy I encountered on my build was on the lathe when it blew apart after a catch. So I have no bowl but the process to build one is good none the less. This is my objective. Start with two pieces of wood, here I’m using cherry and blood wood. I think these were 6×12 by 3/4 inch pieces. Dove tails...

Read this entry »


View degoose's profile

How to make a endgrain tumbling block butcher block board!

08-12-2009 12:13 PM by degoose | 50 comments »

Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed. Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...

Read this entry »


View patron's profile

making a 'bow tie' circle pattern - tutorial

01-10-2011 05:23 AM by patron | 42 comments »

my ‘did it my way board’ http://lumberjocks.com/projects/42141 was done like thisthe tangents are the square of the circlethe thickness of the stock is that height of the squarethe width of the stock is the square and the two wingsof the circle combined(for my 1 1/4” bits it was 1”x1 1/2”).cut and mill the stockrun the round edges firstso the flat is still good for the coves later.the fence and the cutter tangent want to be exactso there is no loss in w...

Read this entry »


View dakremer's profile

Creative Woodworking #35: Interlocking Coasters

08-06-2012 09:46 PM by dakremer | 4 comments »

ZESCH INTERLOCKING COASTERS BY MICHIEL CORNELISSEN ONTWERP

Read this entry »


View lew's profile

Kitchen Treasures #1 Making the Celtic Knot Rolling Pin #1: The Jigs

10-04-2008 01:36 AM by lew | 10 comments »

I have had so many positive comments and feedback on the Celtic Knot Rolling Pin. Thank you for all of them. Many LumberJocks asked for instructions on how they are made- so here goes. I am a fan of “Cook Book” style instructions so if I miss any details, please let me know and I will try to flesh them out. I thought it best to start with the jigs I used to prepare the turning blanks. Please note that I always over engineer everything and hardly ever see the obvious or the easy...

Read this entry »


View Metrotek's profile

ELECTRIC ANGLE SETTING TOOL

03-27-2012 12:37 AM by Metrotek | 6 comments »

Greetings to all; I am attaching scans of a tool that I once made my version of, for setting the table saw blade square to the table. It’s electric running on batteries with a led to indicate. You set it with a steel square on a flat surface; when both pointed probes are touching the blade, the light lights up. They work great and I’m making one after I finished my ersatz Biesmeyer fence. You can get the little battery holders at Radio Shack or simiar.Check out the drawings a...

Read this entry »


View mafe's profile

Scraper shaves my way #1: The family portrait...

05-05-2011 01:10 PM by mafe | 22 comments »

Scraper shaves my waymaking a bunch of scraper shaves Lately I have been making quite a few new handles for old hammers and axes, and the finish has been made with a card scraper.This tool, the scraper starts to show its face to me more and more – when a large burr it can produce shavings, and with a fine burr it can make dust. But most of all it brings a finish that you can never get with sandpaper, it brings out the life of the wood. So when I lately saw several people here on L...

Read this entry »


View Woodhacker's profile

Hand Cut Double Dovetail Experiment

07-03-2008 06:48 AM by Woodhacker | 74 comments »

After admiring the double and double-double dovetail joints that are capable with the Incra and other jigs, I started thinking, “Why not try this by hand?” So this box is my first experiment with handcut double dovetails. It took me some time to figure out the joinery process, but once I realized a few things about this type of joint, it seemed do-able. It was quite challenging but also a ton of fun. It also does take some degree of patience and precision…which I’m still working on. In...

Read this entry »


« prev 1 2 3 4 next »
33 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase