LumberJocks

LumberJocks Woodworking Forums

  • Advertise with us
All Topics Replies Last post
View vsefcik's profile

Freud glue line blade for Bosch 4100-09 table saw

06-30-2013 05:24 PM by vsefcik in Power Tools, Hardware and Accessories

I have a Bosch 4100-09 table saw and I’m considering purchasing a Freud...

10 05-24-2017 09:18 PM
View BalsaWood's profile

Bookcase header and footer movement

05-24-2017 05:52 PM by BalsaWood in Woodworking Skill Share

When building bookcase with a toekick (footer) or header, is it necessary to...

1 05-24-2017 09:15 PM
View JRsgarage's profile

Off-topic content. Click to see the post.

05-22-2017 11:53 PM by JRsgarage in Coffee Lounge

3 05-24-2017 09:15 PM
View chrisb89's profile

Dining table

05-24-2017 06:00 PM by chrisb89 in Woodworking Skill Share

2 05-24-2017 09:07 PM
View Mrowell's profile

Segmented turning ideas

05-19-2017 02:05 AM by Mrowell in Woodturning

Hello everyone!! I am looking to try my hand at segmented turning and am l...

5 05-24-2017 08:28 PM
View gpastor's profile

Woodworking club starting in Akron Canton Ohio

08-13-2012 03:51 PM by gpastor in Woodworking Skill Share

.

6 05-24-2017 08:22 PM
View leftcoaster's profile

Clamp recommendations

05-24-2017 03:40 PM by leftcoaster in Jigs & Fixtures

Hi all I have a few 48” pipe clamps, a bunch of quick clamps and spr...

9 05-24-2017 08:07 PM
View BalsaWood's profile

Dubuque Clamp Works bar clamps

05-24-2017 05:49 PM by BalsaWood in Power Tools, Hardware and Accessories

I was browsing around for some new bar clamps and noticed that the “Adj...

1 05-24-2017 07:44 PM
View rwe2156's profile

Need advice lumber pricing

05-24-2017 11:18 AM by rwe2156 in Wood & Lumber

Going to look at 8/4 Ponderosa pine tomorrow he is asking 1.50. The only p...

3 05-24-2017 05:11 PM
View Scott's profile

FS: Lie Nielsen Plane Set, NEW in Original Boxes and wrapping paper.

05-07-2017 12:47 AM by Scott in Woodworking Trade & Swap

http://www.craftsmanstudio.com/Lie-Nielsen-Plane-Set-p/ai-plane-set.htm Th...

3 05-24-2017 05:08 PM
View kyle123's profile

Grizzly 1023 RLWX vs the other comps

05-24-2017 01:55 PM by kyle123 in Power Tools, Hardware and Accessories

I know this horse has been flogged over and over for the most part, the diffe...

3 05-24-2017 05:07 PM
View richardchaos's profile

Grizzly BAD ENGINEERING

05-20-2017 11:56 PM by richardchaos in Woodworking Skill Share

I have read more and more posts about the semi-crap from Grizzly Tools. A fri...

31 05-24-2017 04:59 PM
View MagicalMichael's profile

Fret Saw vs Coping Saw

05-21-2017 09:44 PM by MagicalMichael in Hand Tools

I’m confused. I own a coping saw, it’s OK. I have watched Rob C...

7 05-24-2017 04:55 PM
View JerryinCreek's profile

5/8" hole, Can I Use a Center Cut End Mill?

05-22-2017 04:15 PM by JerryinCreek in Power Tools, Hardware and Accessories

Need to cut some 5/8” holes approximately 1/16” deep into maple v...

8 05-24-2017 04:33 PM
View GoodwithWood's profile

Cypress planting boxes

05-23-2017 01:19 AM by GoodwithWood in Wood & Lumber

I have 425 bf of Cypresss on the way that I’m building planting boxes o...

15 05-24-2017 01:48 PM
View steliart's profile

Trade - designing sketchup plans for a joining hand plane !

05-20-2017 05:06 PM by steliart in Woodworking Trade & Swap

Trade – designing sketchup plans for a joining hand plane !I need a joi...

3 05-24-2017 01:46 PM
View JoshinDC's profile

Thickness for cherry storage chest/bench

05-21-2017 07:23 PM by JoshinDC in Designing Woodworking Projects

I’m in the design stage of building a storage chest that I also intend ...

7 05-24-2017 12:52 PM
View greatview's profile

New variable speed motor for old Delta lathe

05-21-2017 02:49 PM by greatview in Woodturning

There are several conversations on this topic but I cannot find what I’...

8 05-24-2017 12:51 PM
View SweetTea's profile

Converting 3 phase Delta UniSaw 34-450 to single phase?

05-23-2017 01:22 PM by SweetTea in Power Tools, Hardware and Accessories

Hey guys, I just picked up a Delta/Rockwell UniSaw model 34-450. The problem ...

15 05-24-2017 12:45 PM
View BigJon's profile

Building a Lathe, need some ideas.

05-22-2017 01:58 PM by BigJon in Woodturning

Been turning on a 12” HF lathe the past few years and finally smoked th...

14 05-24-2017 10:58 AM

« prev 1 ... 6 7 8 9 10 11 12 ... 4182 next »
83628 topics

RSS FEED

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com