LumberJocks

LumberJocks Woodworking Forums

  • Advertise with us
All Topics Replies Last post
View juniorjock's profile

Off-topic content. Click to see the post.

04-08-2012 11:50 AM by juniorjock in Coffee Lounge

4 04-10-2012 04:00 AM
View stroml's profile

What kind of chisels are these?

04-08-2012 09:02 PM by stroml in Hand Tools

Hey everyone, I’m just wondering if these are specialty chisels, or ...

10 04-10-2012 03:50 AM
View Joe Lyddon's profile

Off-topic content. Click to see the post.

03-30-2012 09:34 PM by Joe Lyddon in Coffee Lounge

5 04-10-2012 03:46 AM
View Dick, & Barb Cain's profile

Off-topic content. Click to see the post.

04-04-2012 04:28 PM by Dick, & Barb Cain in Coffee Lounge

13 04-10-2012 03:39 AM
View dpwalker's profile

Off-topic content. Click to see the post.

04-09-2012 04:02 AM by dpwalker in Coffee Lounge

3 04-10-2012 03:36 AM
View RussellAP's profile

Need some advice about a jig.

04-09-2012 09:03 PM by RussellAP in Jigs & Fixtures

I make adirondack chairs. The slats for the back are cut from 1×4 stock,...

9 04-10-2012 02:45 AM
View bigfoot62's profile

Grizzly 1023 RLW

02-15-2012 04:56 AM by bigfoot62 in Power Tools, Hardware and Accessories

I’ve just purchused a Grizzly 1023 RLW table saw with the right wing be...

6 04-10-2012 02:06 AM
View derb's profile

Finding hardwood material in Toronto Area

10-04-2011 12:33 AM by derb in Wood & Lumber

know about two places in the Toronto area who sell hardwood material rough lu...

2 04-10-2012 01:57 AM
View Lee Barker's profile

Have you ever seen an iron wood board this large?

04-09-2012 09:12 PM by Lee Barker in Wood & Lumber

Bought this from a guy downtown in a parking lot. Arizona plates. I thought...

6 04-10-2012 01:38 AM
View BlankMan's profile

Craigslist Gloat

04-01-2012 05:13 PM by BlankMan in Power Tools, Hardware and Accessories

I’ve been watching Craigslist the past week for a $10-$20 router I coul...

18 04-10-2012 01:08 AM
View Angry_Bird's profile

Lumber

04-09-2012 12:20 PM by Angry_Bird in Wood & Lumber

looking for advice on how to market lumber. A recent downfall of a walnut lo...

3 04-10-2012 01:07 AM
View gfadvm's profile

Picture Frame Question

04-08-2012 02:40 AM by gfadvm in Woodworking Skill Share

I’ve been making some non-mitered, half lap pic frames and I’m lo...

19 04-10-2012 12:56 AM
View MichaelAgate's profile

What type of wood is this

04-08-2012 08:38 PM by MichaelAgate in Wood & Lumber

Trying to figure out what type of wood this is. I only have a few pieces but ...

6 04-10-2012 12:22 AM
View AffineCreations's profile

Rip cut binds on table saw, best solution?

04-08-2012 06:07 PM by AffineCreations in Safety in the Woodworking Shop

Ripping a 24” long, 7” wide, 1” thick piece of cherry on my...

13 04-09-2012 11:56 PM
View Phil277's profile

New life for bar clamp

04-06-2012 07:54 PM by Phil277 in Hand Tools

I’ve owned this small bar clamp for over 30 years and used it often....

16 04-09-2012 11:55 PM
View GMman's profile

Off-topic content. Click to see the post.

04-09-2012 10:28 PM by GMman in Coffee Lounge

4 04-09-2012 10:44 PM
View degoose's profile

Etsy Store.

01-14-2012 09:04 AM by degoose in Sweating for Bucks Through Woodworking

I opened an etsy.com presence a few months ago… but was a little waywar...

34 04-09-2012 10:18 PM
View Joe Lyddon's profile

Off-topic content. Click to see the post.

04-09-2012 10:07 PM by Joe Lyddon in Coffee Lounge

1 04-09-2012 10:12 PM
View RussellAP's profile

If you cut it short

04-08-2012 04:37 PM by RussellAP in Woodworking Skill Share

I don’t see much use for this, unless you’re drinking while measu...

6 04-09-2012 10:05 PM
View calicoastie's profile

Bagshaw and field?

03-26-2012 03:21 PM by calicoastie in Hand Tools

i picked up a tool set i cant find much information about on and was directed...

3 04-09-2012 10:02 PM

« prev 1 ... 2575 2576 2577 2578 2579 2580 2581 ... 4231 next »
84617 topics

RSS FEED

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com