LumberJocks

LumberJocks Woodworking Forums

  • Advertise with us
All Topics Replies Last post
View Dan'um Style's profile

Off-topic content. Click to see the post.

08-03-2012 10:12 PM by Dan'um Style in Coffee Lounge

11 08-04-2012 10:36 AM
View jgerman's profile

Newbie Question: Diamond Plates

08-04-2012 02:47 AM by jgerman in Hand Tools

If diamond plates are dead flat and don’t wear, why does almost no one ...

9 08-04-2012 10:14 AM
View Gene Howe's profile

A wonderful visit with Shipwright in B.C.

08-03-2012 03:22 PM by Gene Howe in Woodworking Skill Share

After a reunion in WY and a small deck building job in Washington, my wife, h...

8 08-04-2012 05:20 AM
View AngieO's profile

How do I adjust the blade on my table saw to be square?

07-29-2012 02:52 AM by AngieO in Power Tools, Hardware and Accessories

So, I got my table saw from my friend last week. I have been crazy busy this ...

26 08-04-2012 03:54 AM
View chip73's profile

Workbench top

08-04-2012 02:30 AM by chip73 in Woodworking Skill Share

Looking at building a workbench after being inspired by all the Jocks, Howeve...

3 08-04-2012 03:45 AM
View woodworkerscott's profile

Off-topic content. Click to see the post.

08-04-2012 02:06 AM by woodworkerscott in Coffee Lounge

3 08-04-2012 02:25 AM
View FusionHF's profile

Recommended alternative to spraying lacquer for large flat surfaces

08-03-2012 01:21 AM by FusionHF in Finishing

Usually I spray clear SW precat lacquer with my HVLP all day long without any...

12 08-04-2012 01:42 AM
View Arlin Eastman's profile

Off-topic content. Click to see the post.

08-01-2012 04:56 AM by Arlin Eastman in Coffee Lounge

47 08-04-2012 01:31 AM
View Bill St.Pierre's profile

Reclaimed Walnut Log

07-18-2012 11:31 PM by Bill St.Pierre in Wood & Lumber

I have recently dug up this 30’ walnut log on a job I was w...

12 08-04-2012 01:21 AM
View Kernal's profile

Albuquerque Wood Supply

08-01-2012 07:33 AM by Kernal in Wood & Lumber

Hi All, I’m living in Albuquerque and slowly getting into woodworkin...

13 08-04-2012 01:08 AM
View Joe Lyddon's profile

Off-topic content. Click to see the post.

07-19-2012 07:58 PM by Joe Lyddon in Coffee Lounge

114 08-04-2012 12:23 AM
View 12strings's profile

Red (Soft) Maple

08-02-2012 04:42 PM by 12strings in Wood & Lumber

Is This a decent wood for making anything? You hear a lot about hard Maple, ...

5 08-04-2012 12:20 AM
View C_PLUS_Woodworker's profile

Am I the only one that writes all over the white formica outfeed table on my TS?

07-09-2012 06:00 PM by C_PLUS_Woodworker in Focus on the Workspace

In eating lunch so I thought i would ask this. My wife just came out and c...

26 08-03-2012 10:47 PM
View cutworm's profile

They Don't Make Them Like They Used To? Weigh In.

07-31-2012 11:37 PM by cutworm in Power Tools, Hardware and Accessories

What do you think? I waffle here. Some of the old stuff is really good and ...

44 08-03-2012 10:09 PM
View yellowtruck75's profile

Have you ever got an off the wall large consignment order?

08-03-2012 09:58 PM by yellowtruck75 in Woodworking Skill Share

I like hopefully alot of you would like to someday make a living off my woodw...

0 08-03-2012 09:58 PM
View Joe Lyddon's profile

Off-topic content. Click to see the post.

08-03-2012 09:46 PM by Joe Lyddon in Coffee Lounge

0 08-03-2012 09:46 PM
View Newage Neanderthal's profile

Off-topic content. Click to see the post.

08-02-2012 10:54 PM by Newage Neanderthal in Coffee Lounge

11 08-03-2012 09:37 PM
View Kookaburra's profile

General finishing advice

08-02-2012 04:26 PM by Kookaburra in Finishing

There is so much advice and opinon in this forum about specific finishes and ...

22 08-03-2012 09:31 PM
View dakremer's profile

Awesome new hardware. Question....

08-02-2012 12:13 PM by dakremer in Jigs & Fixtures

I have a new prototype I’m working on and want to incorporate these hin...

45 08-03-2012 09:13 PM
View Quanter50's profile (online now)

Looking for handwheels Rockwell/Delta 37-315

07-29-2012 01:24 AM by Quanter50 in Woodworking Trade & Swap

Looking high and low for handwheels. I think the originals were either 4̶...

8 08-03-2012 09:12 PM

« prev 1 ... 2157 2158 2159 2160 2161 2162 2163 ... 3987 next »
79721 topics

RSS FEED

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com