LumberJocks

LumberJocks Woodworking Forums

  • Advertise with us
All Topics Replies Last post
View lashomb's profile

My new engraved Stanley Jack by Layne Zuelke

11-17-2011 06:54 AM by lashomb in Hand Tools

Type 16, engraved by Layne Zuelke of Cajun Handplanes Really cool guy, and...

7 11-17-2011 04:47 PM
View Brett's profile

Qs about oilstones

11-17-2011 04:55 AM by Brett in Hand Tools

Is an 8”x2” oilstone wide enough to sharpen plane irons? Should ...

6 11-17-2011 04:21 PM
View jonnytranscend's profile

makita 18 volt impact driver

11-11-2011 07:30 PM by jonnytranscend in Woodworking Trade & Swap

This is for a slightly used 18 volt makita impact. It comes with batteries, c...

4 11-17-2011 04:19 PM
View richgreer's profile

Router table fences - offset capability

11-09-2011 06:57 PM by richgreer in Power Tools, Hardware and Accessories

I just read a very well written and comprehensive review of Woodpecker’...

18 11-17-2011 04:16 PM
View Sunnygirl's profile

New to Spraying, Need an Opinion

11-16-2011 09:53 PM by Sunnygirl in Finishing

I’m getting ready to buy a turbine HVLP, have only sprayed one time in ...

10 11-17-2011 04:12 PM
View DamnYankee's profile

How do you use your bandsaw box?

11-11-2011 08:58 PM by DamnYankee in Designing Woodworking Projects

Got a used bandsaw a while back, got it up and running, and was looking at id...

9 11-17-2011 03:55 PM
View gani's profile

unisaw tilting shaft

11-18-2011 11:16 AM by gani in Woodworking Trade & Swap

I need a tilting worm shaft assembly, if anyone has it and willing to sell, l...

0 11-17-2011 03:33 PM
View MsDebbieP's profile

LJ eMag - November 2011

11-16-2011 12:38 PM by MsDebbieP in LumberJocks.com Site Feedback

the Nov 2011 issue of our eMag is now available Feedback is appreciated ...

7 11-17-2011 11:37 AM
View Rick's profile

Off-topic content. Click to see the post.

11-09-2011 11:30 AM by Rick in Coffee Lounge

9 11-17-2011 09:08 AM
View Ron Ramsey's profile

HELP! I'm Looking for A specific Jewelry Box Plan

11-17-2011 02:37 AM by Ron Ramsey in Designing Woodworking Projects

I recently had a magazine that had several keepsake type box plans, but I hav...

3 11-17-2011 08:46 AM
View Garoad's profile

How do I make this? Should I make it? =)

11-17-2011 06:00 AM by Garoad in Designing Woodworking Projects

I’m attaching a diagram for a “plan” (so-called, aka the ne...

1 11-17-2011 06:04 AM
View HorizontalMike's profile

Off-topic content. Click to see the post.

11-05-2011 03:01 PM by HorizontalMike in Coffee Lounge

16 11-17-2011 05:44 AM
View JohnT05's profile

Crosscut saw ID

11-15-2011 11:22 PM by JohnT05 in Hand Tools

Hi,I recently purchased a saw and I wanted to ask a few questions to try to l...

1 11-17-2011 05:37 AM
View SawdustDon's profile

Jointer and Drill Press Time Needed near Fayetteville NC

11-16-2011 12:36 PM by SawdustDon in Woodworking Trade & Swap

Trying to finish up the vise on my workbench and I just can’t get the f...

3 11-17-2011 05:08 AM
View elvis's profile

Leigh jig alignment?

10-12-2008 01:35 AM by elvis in Power Tools, Hardware and Accessories

I have a D4 and for some reason am having difficulty aligning the side with t...

5 11-17-2011 04:54 AM
View chrisstef's profile

gaps and cracks .. any repair tips?

11-08-2011 02:21 AM by chrisstef in Woodworking Skill Share

So ive been working on and off on a football carved from a green piece of Map...

17 11-17-2011 03:46 AM
View Frank Hicken's profile

Leigh jigs D4 AND DR4 ?????????????

12-13-2009 10:42 PM by Frank Hicken in Power Tools, Hardware and Accessories

Newbie question, what is the difference between the leigh dovetail jigs, 24 ...

3 11-17-2011 02:36 AM
View lukedevilliers's profile

How to sand in between chair back spindles?

03-25-2011 05:42 AM by lukedevilliers in Power Tools, Hardware and Accessories

Hello and thanks all for your time. Newbie question here. I’m ref...

5 11-17-2011 02:27 AM
View Bill1225's profile

Off-topic content. Click to see the post.

11-13-2011 04:46 AM by Bill1225 in Coffee Lounge

9 11-17-2011 02:25 AM
View peter blair's profile

wood Lathe - Bowl Bottom Finder

11-17-2011 01:46 AM by peter blair in Jigs & Fixtures

Have you ever gone through the bottom of a bowl? I sure have!Too frequently a...

0 11-17-2011 01:46 AM

« prev 1 ... 2024 2025 2026 2027 2028 2029 2030 ... 3460 next »
69188 topics

RSS FEED

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com