LumberJocks Woodworking Forums

  • Advertise with us
All Topics Replies Last post
View axam's profile

Table Saw tricks & tips suggestions

08-16-2016 12:43 PM by axam in Power Tools, Hardware and Accessories

Hi Was wondering if there were any tips you could impart about table saws...

14 08-20-2016 02:01 PM
View treesner's profile

Cordless jigsaw blows sawdust away

08-07-2016 07:00 PM by treesner in Power Tools, Hardware and Accessories

I’ve been gettin a ton of use out of my big saw now that it’s cor...

5 08-20-2016 01:22 PM
View JoeinGa's profile

Off-topic content. Click to see the post.

08-11-2016 11:17 PM by JoeinGa in Coffee Lounge

12 08-20-2016 01:07 PM
View GR8HUNTER's profile

Thanks Mike Short

08-19-2016 05:13 PM by GR8HUNTER in Woodcarving

A HUGE THANKS to Mike Short carver of the little guys ,we received our Sa...

3 08-20-2016 11:28 AM
View thelt's profile

WoodSmith Plans Email on 8-20-2016

08-20-2016 11:21 AM by thelt in Finishing

Anyone interested in the Fold-up Finishing Station that was featured in the W...

0 08-20-2016 11:21 AM
View Rushman's profile

Selecting Walnut Project Lumber

09-30-2009 07:22 PM by Rushman in Designing Woodworking Projects

Over the last couple months I have bought many board feet of Walnut from a la...

19 08-20-2016 10:51 AM
View WoodHoarder's profile

Avoiding Sagging-Design Critique

06-26-2016 09:02 PM by WoodHoarder in Designing Woodworking Projects

Hello All, I have been working on a cedar driveway gate the past sever...

24 08-20-2016 10:35 AM
View Big_T's profile

Which 2 bandsaw band saw blades for curves and resaw on Laguna 1412?

08-14-2016 07:36 AM by Big_T in Power Tools, Hardware and Accessories

Just ordered a Laguna 1412 a couple hours ago and wondering what is the best ...

11 08-20-2016 06:24 AM
View Maxlynch99's profile

Beiginner woodworking?

08-16-2016 06:03 AM by Maxlynch99 in Designing Woodworking Projects

I’m new to word working but my grandpa has a shop full of shopsmith too...

16 08-20-2016 04:06 AM
View customdept's profile

Choosing the right Sliding table saw & edgebander

08-15-2016 12:45 PM by customdept in Power Tools, Hardware and Accessories

Hey Everyone! I’m currently looking to purchase a used sliding table...

2 08-20-2016 03:23 AM
View bbasiaga's profile

Help with z clip table top fasteners

07-11-2016 03:01 AM by bbasiaga in Power Tools, Hardware and Accessories

I have some z clip fasteners that I was planning to use to hold my table top ...

4 08-20-2016 02:55 AM
View langski93's profile

Ever See This Dovetail Technique?

08-15-2016 02:14 AM by langski93 in Woodworking Skill Share

I was at Jamestown VA this past week and saw this period trunk. The photos ar...

7 08-20-2016 02:35 AM
View victoryss364's profile

Picture Frame Glass

08-18-2016 01:40 PM by victoryss364 in Power Tools, Hardware and Accessories

Does anyone know where I can buy precut glass and backing for picture frames?...

12 08-20-2016 01:41 AM
View HillWilly's profile

Radial arm saw [REPURPOSING]

08-20-2016 01:23 AM by HillWilly in Power Tools, Hardware and Accessories

I have been looking for something to do with the other end of my RAS motor be...

0 08-20-2016 01:23 AM
View PatrickIrish's profile

Unisaw I.D. Help. Worth $750?

08-17-2016 04:41 AM by PatrickIrish in Power Tools, Hardware and Accessories

I’m looking at a used Delta Unisaw Platinum Edition with an Excalibur g...

12 08-19-2016 11:33 PM
View poopiekat's profile

Another "Whatizzit" for My Tool Depository

08-19-2016 02:32 AM by poopiekat in Hand Tools

I found a small cache of tools at a thrift shop, likely from some dead old ma...

11 08-19-2016 10:52 PM
View Brat700's profile

Off-topic content. Click to see the post.

08-16-2016 02:13 PM by Brat700 in Coffee Lounge

4 08-19-2016 10:41 PM
View Mike_D_S's profile

DIY drum sander parts (was Performax parts)

08-16-2016 03:50 AM by Mike_D_S in Woodworking Trade & Swap

So with essentially no interest in the conveyor parts and before I strip it d...

3 08-19-2016 09:51 PM
View vonfalken's profile

table saw

08-18-2016 01:26 PM by vonfalken in Power Tools, Hardware and Accessories

good morning,,the trunnion on my delta table saw broke so im thinking about a...

10 08-19-2016 09:43 PM
View Vern Leonard's profile

Zero clearance insert

08-18-2016 01:40 PM by Vern Leonard in Jigs & Fixtures

I am a long time lurker at this site. I recently purchased a new rigid table ...

6 08-19-2016 09:23 PM

« prev 1 ... 8 9 10 11 12 13 14 ... 3894 next »
77880 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics