Power Tools, Hardware and Accessories Forum

  • Advertise with us

Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be an overwhelming adventure, and you have some tough decisions to make. Welcome to the Woodworking Forum that allows you to seek and find essential information from other like-minded folks who have walked the same path before.

Topics Replies Last post
View OllieNorth's profile

Finding Replacement European Hinge with mount 90 degrees from door

03-06-2018 03:33 AM by OllieNorth

I have a bathroom medicine cabinet with three doors. One of the hinges broke ...

3 03-06-2018 04:20 PM
View BadMojo's profile

Rigid 4512 v Delta 36-725 - Size Comparrison?

03-05-2018 02:54 PM by BadMojo

A 1st-time poster here. Enjoying the wealth of knowledge already. I’...

5 03-06-2018 03:45 PM
View Lsteiger's profile

Grizzly “Scroll saw” identification

03-06-2018 02:14 PM by Lsteiger

Hey all I was cruising craigslist and found this post, the seller Doesn’t see...

1 03-06-2018 02:38 PM
View KipD's profile

what gauge for 3hp Unisaw leed in wire?

03-03-2018 03:29 AM by KipD

1989 34-806 type 2 Unisaw has new Leeson 3hp single phase 230V motor 120728.0...

7 03-06-2018 10:07 AM
View ProfPenguin's profile

Rockwell 34-345 Table Saw -- Fix or Part out?

04-02-2013 08:49 AM by ProfPenguin

Hi Lumberjocks, I’ve been lurking here for a long time and love the ...

21 03-06-2018 05:35 AM
View Ron Ford's profile

Anyone Use the Nova DVR Drill Press Yet?

01-07-2017 10:14 PM by Ron Ford

The new Nova DVR drill press looks like areal home run. One of my friends ha...

26 03-06-2018 03:44 AM
View ChicksWithTools's profile

Drill Bits

03-04-2018 07:48 PM by ChicksWithTools

I just finished a simple project of putting new hardware on a dresser which r...

20 03-05-2018 11:28 PM
View robinwis's profile

Old Table Saw

03-05-2018 02:54 PM by robinwis

Should my table saw blade spin freely when not connected to the motor? I rece...

6 03-05-2018 07:23 PM
View Brett's profile

Did I make a mistake?

03-01-2018 09:19 PM by Brett

Hi all. I recently purchased a Powertech 1HP wall mount dust collector (it...

13 03-05-2018 05:06 PM
View Steven H's profile

Carter Stabilizer

06-01-2011 06:49 AM by Steven H

Im still figuring out if I should spend it on Carter Stabilizer for my Grizzl...

28 03-05-2018 04:23 PM
View Ben's profile

Slow speed grinder on the fritz

03-04-2018 05:22 PM by Ben

I have a Woodcraft slow speed grinder – about 9 years old and seen very...

5 03-05-2018 02:24 PM
View ded's profile

Complete newbie needs advice, direction!

03-04-2017 10:05 PM by ded

Greetings all, short time lurker but finally signed up! Sorry for this being ...

8 03-05-2018 01:11 PM
View Picklehead's profile

What's the highest useful grit on a stationary belt sander?

11-02-2014 11:06 AM by Picklehead

I just picked up a combo belt/disk sander off CL. (9 inch disk + 6×48 be...

27 03-05-2018 01:06 PM
View Justahunk's profile

Heatd of this Jointer

03-04-2018 04:33 PM by Justahunk

You guys are my last hope as I haven’t been able to find anything on this bra...

5 03-05-2018 10:33 AM
View optimusprimer92's profile

Square cut on one side of table saw only

03-05-2018 02:33 AM by optimusprimer92

I have had run out issues with my Delta 36-725 and am unable to fix it with a...

23 03-05-2018 09:45 AM
View Winny94's profile

Fence recommendation for craftsman 110 table saw?

03-05-2018 03:03 AM by Winny94

What are some suggestions for a decent fence (that won’t break the bank...

2 03-05-2018 05:25 AM
View wthwaites's profile

Which Dust Collector to Buy?

03-04-2018 04:33 PM by wthwaites

Hello All, I have a small workshop and no dust collection system in place....

8 03-05-2018 04:39 AM
View Rayne's profile

Suggestions on what to do with an empty tool stand

03-05-2018 12:08 AM by Rayne

Good Evening LJ’s, I’m looking for suggestions on what I co...

6 03-05-2018 03:15 AM
View leftcoaster's profile

Need a photo - ridgid oscillating belt and spindle sander

03-04-2018 09:09 PM by leftcoaster

Can someone post a close up photo of the belt piece of this sander ? Specifi...

2 03-05-2018 02:50 AM
View Dwain's profile

Craftsman Parks Planer - Bringing it to life, but a problem...

01-13-2018 05:20 AM by Dwain

I am trying to get an old 1950’s vintage Craftsman Parks planer running...

8 03-05-2018 01:26 AM

« prev 1 ... 6 7 8 9 10 11 12 ... 1393 next »
27857 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics