Power Tools, Hardware and Accessories Forum

  • Advertise with us

Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be an overwhelming adventure, and you have some tough decisions to make. Welcome to the Woodworking Forum that allows you to seek and find essential information from other like-minded folks who have walked the same path before.

Topics Replies Last post
View egel's profile

plaing wet oak

10-14-2010 08:51 PM by egel

I have a job that I need to plane some frash sawed white oak to size (2×...

1 10-14-2010 08:57 PM
View Hobbywood's profile

Choosing the Right Router

10-12-2010 04:39 PM by Hobbywood

Since most anyone has had more experience in a wood shop than I have, I would...

11 10-14-2010 03:19 PM
View semi75's profile

Worksharp 3000

10-13-2010 11:51 PM by semi75

I don’t know if many of you all use the Worksharp but they are having a...

6 10-14-2010 02:42 PM
View jal's profile

assembly a porter cable jobsite table saw

10-13-2010 02:59 PM by jal

I am unable to insert the push-stick storage holder into the slots/holes in t...

1 10-14-2010 04:53 AM
View dbhost's profile

Drill bit size to drill holes for router bit shanks.

10-12-2010 09:16 PM by dbhost

I know this might seem like a dumb question, but it would seem obvious that i...

15 10-14-2010 04:03 AM
View Imacman's profile


10-10-2010 02:44 AM by Imacman

Hi All… As some are aware, I’m getting lose to completing my back...

12 10-14-2010 02:35 AM
View JCantin's profile

Hammer drills and pilot holes and Chilean miners

10-13-2010 09:01 PM by JCantin

Not woodworking related but an interesting story about how the rescue options...

0 10-13-2010 09:01 PM
View linesoflux's profile

Replacing a pulley/arbor key

10-13-2010 08:10 PM by linesoflux

I just replaced an arbor and bearings on a 20yr old craftsman tablesaw. I nee...

3 10-13-2010 08:38 PM
View Raymond's profile

Well I finally purchased my compressor

10-11-2010 04:23 PM by Raymond

I finally purchased my compressor. I went with the Puma, looks like a good un...

4 10-13-2010 06:16 PM
View jtlighting's profile

delta hybrid saw vibration

05-18-2010 07:19 AM by jtlighting

hello all. i am new to LJ and would like to first say hello and praise everyo...

16 10-13-2010 12:13 PM
View richgreer's profile


07-06-2010 09:06 PM by richgreer

I see that Bridge City’s Jointmakers have been discussed on this site b...

6 10-13-2010 08:51 AM
View Mark Blomster's profile

Does anyone have feedback on sharpening Forrest blades?

10-07-2010 06:59 PM by Mark Blomster

I have 3 Forrest Woodworker II blades that I rotate in/out after cleaning the...

15 10-13-2010 06:24 AM
View Thomas Keefe's profile

Question about rust

09-30-2010 09:56 PM by Thomas Keefe

Recently I bought a hand plane on ebay and it had some very light rust. The r...

14 10-13-2010 06:07 AM
View morty's profile

Curved sole on bench plane?

10-11-2010 08:57 PM by morty

Hi, I have a new Buck Bros. bench plane and I was testing it out on a smal...

9 10-13-2010 01:16 AM
View mickeyw's profile

Nitrile Gloves Are Great.

10-12-2010 10:00 PM by mickeyw

I picked up a five pack of large Nitrile work gloves at Home Depot. Had seen ...

2 10-12-2010 11:06 PM
View JamieH's profile

Weekend tool score!

10-11-2010 02:45 AM by JamieH

Well, I went and pulled the trigger on the hand planes at the local antique s...

10 10-12-2010 08:24 PM
View BreakingBoardom's profile

Anyone Looking For A Dado Set?

10-06-2010 09:05 PM by BreakingBoardom

If anyone is looking for a low-cost dado blade set that has gotten very good ...

1 10-12-2010 03:24 PM
View mrg's profile

Rip Fence

10-11-2010 05:45 PM by mrg

I am looking at replacing the fence on my Delta contractor saw and I am betwe...

2 10-12-2010 01:28 AM
View Moron's profile


05-10-2010 12:49 PM by Moron

Cry me a river ? I went to an auction on Saturday and having little spare cha...

2 10-12-2010 01:00 AM
View jaydubya's profile

new table saw and blade question

10-10-2010 04:21 AM by jaydubya

Just put my new table saw on layaway at sears. its a C-man 21833. 3 easy paym...

7 10-11-2010 04:04 PM

« prev 1 ... 891 892 893 894 895 896 897 ... 1204 next »
24080 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics