LumberJocks

Power Tools, Hardware and Accessories Forum

  • Advertise with us

Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be an overwhelming adventure, and you have some tough decisions to make. Welcome to the Woodworking Forum that allows you to seek and find essential information from other like-minded folks who have walked the same path before.

Topics Replies Last post
View TheKingInYellow's profile

I hate Boeshield T-9, need advice on rust issues...

06-26-2011 07:00 PM by TheKingInYellow

My one and half week old contractor’s saw is already developing some ru...

59 08-31-2011 02:43 PM
View WoodworkingGeek's profile

table saw question...

08-29-2011 09:00 PM by WoodworkingGeek

Hi LJ’s!!I looking into getting a table saw and have a few on cregslist...

15 08-31-2011 01:28 PM
View ewell's profile

Table saw input needed

08-29-2011 09:58 PM by ewell

Talking to someone about buying the delta 36-750 model table saw. Doesnt hav...

13 08-31-2011 01:16 AM
View xwingace's profile

Husqvarna 435 16" Chainsaw Starting Problems

08-29-2011 03:53 AM by xwingace

Got me a brand new chainsaw, but damned if I can get the thing to run. After ...

9 08-30-2011 11:47 PM
View gemcam's profile

Delta 22-790x planer-- should I buy one?

08-30-2011 09:10 PM by gemcam

I’m thinking of buying a Delta 22-790x planer but can’t find any ...

0 08-30-2011 08:15 PM
View tworst's profile

What is a reasonable flatness spec for jointer infeed/outfeed tables?

09-06-2010 05:40 AM by tworst

Does anyone know what can of spec to look for on table flatness for a jointer...

12 08-30-2011 06:52 PM
View Logan Windram's profile

Bandsaw Blade Issue?

08-30-2011 05:31 AM by Logan Windram

So I bought a new Olson Flexback 1/2 bandsaw blade, and I can see a slight be...

1 08-30-2011 02:13 PM
View andy49's profile

DeWalt RAS (1400) Motor Issue - help please!

08-15-2011 04:22 AM by andy49

Hi guys, am a newbie to the site and am looking forward to being a part of it...

19 08-30-2011 01:43 PM
View MrDan's profile

Forrest Woodworker II not performing

08-29-2011 01:07 AM by MrDan

Hello all, I finally saved enough pennies to buy the coveted Forrest Woodw...

20 08-30-2011 11:04 AM
View Wintersedge's profile

Are these router bits a good buy?

04-05-2010 08:43 AM by Wintersedge

I am looking into getting a router that will support 1/2” shank bits. I...

27 08-30-2011 07:52 AM
View James 's profile

Electrical Help Needed

08-29-2011 06:30 AM by James

I just bought a table saw from CL and it runs on 220v. I do have 220 in my ho...

15 08-30-2011 07:02 AM
View LatheMan's profile

Boice-Crane 42" Bed Lathe

05-12-2008 07:15 PM by LatheMan

I was recently given a Boice-Crane 42” Bed Lathe, and have successfully...

2 08-30-2011 03:54 AM
View Greg In Maryland's profile

Shop Fox Lathe

08-28-2011 06:32 PM by Greg In Maryland

Hi I am thinking about dipping my toes into turning and thought that this ...

8 08-30-2011 12:29 AM
View agallant's profile

Raoibi 5" disk sander vs DeWault

08-29-2011 07:20 PM by agallant

I currently have been using a Rayobi 5” disk sander. It works well but ...

2 08-29-2011 08:08 PM
View MNWOODWORKER's profile

Very pleased with Festool

08-23-2011 08:47 AM by MNWOODWORKER

I have several Festool tools and I have always been very happy. I did however...

3 08-29-2011 06:38 PM
View TomFran's profile

HVLP guns

07-19-2007 01:37 AM by TomFran

Hello Friends, Does anybody know how much “better” an HVLP spr...

25 08-29-2011 02:57 AM
View SlaterNation's profile

How to wire up Grizzly safety switch for router table (no ground?)

08-28-2011 08:03 PM by SlaterNation

I purchased this switch from Grizzly for use on my router table. I have i...

4 08-29-2011 02:39 AM
View sgtq's profile

Need some helpful advice on a TS deal

08-23-2011 05:07 AM by sgtq

I have the opportunity to purchase a fairly used but well taken care of Ridgi...

35 08-29-2011 02:13 AM
View Beginningwoodworker's profile

Framing Nailing?

08-26-2011 03:50 AM by Beginningwoodworker

I am wondering would a Paslode F350 Framing Nailer work on my Bostitch Trim A...

12 08-28-2011 09:41 PM
View newplane's profile

Craftsman 3 in 1 Rotary Bench

08-24-2011 04:38 AM by newplane

Hello friends, I acquired a discontinued Craftsman 3 in 1 Rotary Bench and...

2 08-28-2011 09:07 AM

« prev 1 ... 764 765 766 767 768 769 770 ... 1227 next »
24535 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com