Power Tools, Hardware and Accessories Forum

  • Advertise with us

Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be an overwhelming adventure, and you have some tough decisions to make. Welcome to the Woodworking Forum that allows you to seek and find essential information from other like-minded folks who have walked the same path before.

Topics Replies Last post
View JasonIndy's profile

The most interesting man in the world...

01-11-2011 06:21 AM by JasonIndy

..has got to be Grizzly’s president. So I got my annual Grizzly catalo...

18 01-15-2011 04:55 PM
View mrjoeg's profile

Owner feedback for Grizzley G07159 10" hybrid table saw

01-15-2011 03:10 AM by mrjoeg

Hello,I am new to this site, and in the beginning phase of a new hobby it the...

2 01-15-2011 05:53 AM
View TopamaxSurvivor's profile

Oneway Stronghold or Talon?????????

01-14-2011 09:13 PM by TopamaxSurvivor

Dear turing aficionados, My lathe is a Craftsman that will turn 16”...

6 01-15-2011 03:58 AM
View brianlsu43's profile

Table Saw HP

01-12-2011 09:40 PM by brianlsu43

Is there a noticeable difference in performance between table saws with 2hp a...

16 01-15-2011 01:12 AM
View Adrian A's profile

Should I choose based on Dust Collector? Sawstop vs Grizzly Cabinet Saw

01-14-2011 07:28 PM by Adrian A

Ive been borrowing a nice Jet 1.5HP 52” Contractor Saw, and its about t...

17 01-14-2011 11:46 PM
View Rod_B's profile

Grizzly Table Saws - G0690 vs G1023RL

01-14-2011 09:42 PM by Rod_B

I’m ready to upgrade to a 3hp cabinet saw. Considering Grizzly G0690 o...

4 01-14-2011 11:25 PM
View woodman44's profile

Choosing the best low cost scroll saw for a 1st time scroller

01-13-2011 10:11 PM by woodman44

I am researching the web for a 16” scroll saw that accepts both the pin...

7 01-14-2011 09:27 PM
View Alongiron's profile

Drill press not seeming to be turning perfectly

01-14-2011 06:23 PM by Alongiron

I have a Rigid DP-1550 stationary drill press. The chuck locked up so I had t...

2 01-14-2011 06:37 PM
View NBeener's profile

Rockler now carrying Laguna Tools

01-13-2011 09:02 PM by NBeener Can Rockler enhance th...

7 01-14-2011 09:38 AM
View Hartmann's profile

Delta sold again.

01-08-2011 01:43 AM by Hartmann

The new owner, TOTY from Taiwan, check it out: http://blog.woodworking-mag...

27 01-14-2011 06:17 AM
View Paul Pomerleau's profile

Verification of Table Saw Tuning

01-14-2011 12:46 AM by Paul Pomerleau

I inherited my dads Craftsman 10” table saw many years ago where it was...

6 01-14-2011 05:16 AM
View flyingoak's profile

Help with a Lathe

01-14-2011 03:46 AM by flyingoak

Ok boys I need some advice. I just bought a Jet JWL-1236 lathe from the wi...

1 01-14-2011 04:08 AM
View Cliff De Witt 's profile

Work Sharp 2000

01-13-2011 10:41 PM by Cliff De Witt

Not to kick over another hornets nest but I was at my local Westlake Ace Hard...

3 01-13-2011 11:05 PM
View TopamaxSurvivor's profile

Chris Schwartz posts a temporary kiln

01-13-2011 02:05 PM by TopamaxSurvivor

Not sure I would want to leave this unattended without a good fire alarm and ...

3 01-13-2011 11:01 PM
View Jon_in_BK's profile

need advice on bevel grinding

01-13-2011 05:18 PM by Jon_in_BK

Hi, I’m just getting started in WW and recently acquired an old hand pl...

8 01-13-2011 10:59 PM
View agallant's profile

Sawstop 3HP wire up.

01-13-2011 08:07 PM by agallant

In getting ready for my new 3hp saw stop I have wired up my shop with 240. Do...

3 01-13-2011 08:30 PM
View yellowtruck75's profile

Problems with my Triton 3 1/4HP Plunge Router

01-13-2011 04:59 PM by yellowtruck75

I am having issues with my Triton 3 1/4HP Plunge Router. It doesn’t wa...

4 01-13-2011 07:31 PM
View newbiewoodworker's profile

CFM data for D55141 Compressor

01-13-2011 07:22 PM by newbiewoodworker

Dear Brendan, we believe the following information addresses your inquiry. ...

0 01-13-2011 07:22 PM
View Blayne's profile

Bartley Gel Stains -- acceptable replacement?

07-29-2010 11:50 PM by Blayne

I recently read an article named Mission Oak Finish by Jeff Jewitt on The Woo...

8 01-13-2011 06:28 PM
View Nick's profile

need help!!!!!! on turing tools for first time bowl turn

01-13-2011 07:50 AM by Nick

Hello, I’m really wanting to start bowl turning but I don’t know ...

2 01-13-2011 04:26 PM

« prev 1 ... 763 764 765 766 767 768 769 ... 1118 next »
22351 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics