Power Tools, Hardware and Accessories Forum

  • Advertise with us

Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be an overwhelming adventure, and you have some tough decisions to make. Welcome to the Woodworking Forum that allows you to seek and find essential information from other like-minded folks who have walked the same path before.

Topics Replies Last post
View leojepace's profile

Wiring help for old craftsman capacitor motor

09-29-2010 04:51 AM by leojepace

Hello, I recently bought an old craftsman table saw with a 3/4 HP capacito...

1 09-29-2010 05:26 AM
View plantek's profile

Bench Top Planer

09-28-2010 05:40 AM by plantek

Hello Lumber Jocks, I just bought the DeWalt 734 bench top planer. I did a...

14 09-29-2010 04:10 AM
View 2xmahi's profile

has anyone used the dovetail jig from harbor freight? If so any reviews???

09-17-2009 08:10 PM by 2xmahi

i am thinking of purchasing it as a starter just to try and learn the basics ...

5 09-29-2010 02:57 AM
View Ken Fitzpatrick's profile

Keeping a computer from freezing in an unheated space

09-28-2010 07:17 PM by Ken Fitzpatrick

Not sure what forum this should be under but I will try it here. Hope that i...

11 09-28-2010 11:16 PM
View Sampson7810's profile

Need to get rid of some older tools

09-27-2010 10:41 PM by Sampson7810

I went up in the attic of my new house and found a Drill Press,Bandsaw,and Pl...

11 09-28-2010 08:07 PM
View ajb's profile

Zero Clearance insert for Craftsman table saw

09-28-2010 07:30 AM by ajb

So the question is has any one been able to make a zero clearance insert for ...

5 09-28-2010 06:24 PM
View Mark's profile

Very impressed with easy trick for my table saw.

09-25-2010 04:51 PM by Mark

This has been mentioned before about using thin kerf blades on your table saw...

16 09-28-2010 05:09 PM
View Noab's profile

8" Bench Grinder Recommendation

09-28-2010 04:20 PM by Noab

What’s a good 8” bench grinder?

2 09-28-2010 04:42 PM
View MoBirdman's profile

Blade Stops Turning

09-27-2010 02:58 AM by MoBirdman

Hi folks…need a little help.I purchased this saw (older Craftsman) seve...

11 09-28-2010 03:49 PM
View lazyborn1's profile

dw735 planer baldes replacement

09-27-2010 06:36 PM by lazyborn1

Hello LJs,I am trying to change the blades on my dw735 planer. Unfortunately,...

5 09-28-2010 02:26 PM
View HarleySoftailDeuce's profile

building a right side table saw extension support for an Excalibur dust collector hood.

09-28-2010 02:28 AM by HarleySoftailDeuce

Hello LJ members, I purchased an Excalibur dust collector hood for my Gene...

2 09-28-2010 01:51 PM
View bunkie's profile

Bench Dog ProMax Question

09-28-2010 04:38 AM by bunkie

I’m considering getting a Bench Dog ProMax cast iron router table that ...

1 09-28-2010 06:11 AM
View Steven H's profile

Tool holder/pouch

09-26-2010 06:32 AM by Steven H

I looking for a tool pouch that can clip on to my belt and ready to go. It sh...

4 09-28-2010 01:47 AM
View JayPique's profile

Butt Mortise Chisels - reviews, recommendations, suggestions

09-25-2010 07:46 PM by JayPique

I find myself frequently wishing that I had a set of shorter chisels to use i...

8 09-28-2010 01:26 AM
View Donlore's profile

Pin routers plans

09-26-2010 09:50 PM by Donlore

Does anyone know of a good set of plans to build an overhead pin router? I...

1 09-27-2010 06:14 PM
View ClayandNancy's profile

Boice Crane 8" jointer

09-27-2010 04:14 AM by ClayandNancy

I’m looking at a Boice Crane 8” jointer circa 1954, was wondering...

2 09-27-2010 04:13 PM
View terry603's profile

new saw

09-26-2010 09:44 PM by terry603

finally got a new saw. a ridgid r4510. because of the high reviews on lumbe...

5 09-27-2010 12:30 PM
View newbiewoodworker's profile

How do you justify the cost?

09-19-2010 03:59 AM by newbiewoodworker

This is a quesiton that has bothered me from day one… How do you justi...

85 09-27-2010 10:38 AM
View RandyMarine's profile

Mill File for Cabinet scrapper sharpening.

09-20-2010 05:08 PM by RandyMarine

Hello Fello LJ’s, I am building a sharpening station to orginize my ...

14 09-27-2010 05:14 AM
View jtmek's profile

Need Small letter router templates

09-27-2010 02:52 AM by jtmek

I need some really small letter templates for a production router job. Maybe ...

0 09-27-2010 02:52 AM

« prev 1 ... 747 748 749 750 751 752 753 ... 1057 next »
21139 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics