Power Tools, Hardware and Accessories Forum

  • Advertise with us

Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be an overwhelming adventure, and you have some tough decisions to make. Welcome to the Woodworking Forum that allows you to seek and find essential information from other like-minded folks who have walked the same path before.

Topics Replies Last post
View agroom's profile

Need a table saw but have limited space

02-27-2012 05:37 PM by agroom

I finally built a small workshop in my 1 car garage this fall (it’s the...

19 02-28-2012 10:34 PM
View gragian's profile

Decisions, decisions...

02-28-2012 09:12 PM by gragian

This is a follow up to an earlier post asking for advice on what additional i...

3 02-28-2012 09:39 PM
View pielady's profile

Powermatic band saw

02-28-2012 08:13 PM by pielady

i am looking for a table for a Powermatic band saw, either model 141 or 143. ...

1 02-28-2012 09:23 PM
View guitarchitect's profile

fair prices for a rockwell 37-220?

02-28-2012 01:48 AM by guitarchitect

I found a rockwell 37-220 on kijiji in my area for $450. I feel like thatR...

7 02-28-2012 05:53 PM
View dspahn's profile

Advice needed

02-16-2012 09:48 AM by dspahn

I currently own a pretty pathetic Ryobi table saw. And I’m always trol...

44 02-28-2012 04:23 PM
View Blackie_'s profile

1301 Ryobi Planer not planing correclty

02-27-2012 11:41 AM by Blackie_

I was hoping someone might be able to shed some light on this for me. The pro...

12 02-28-2012 01:34 PM
View tsdahc's profile

Looking for info and comments on the Grizzly G0715P table saw

02-27-2012 05:26 AM by tsdahc

I asked for a new table saw for christmas and was gifted a Bosch 4100. Now I...

5 02-28-2012 12:20 PM
View Vrtigo1's profile

Harbor freight dust collector power draw

02-28-2012 05:00 AM by Vrtigo1

I relocated my dust collector this past weekend and had to run a new circuit ...

2 02-28-2012 07:07 AM
View cajun_duck's profile

compressor and nailer confusion

02-27-2012 09:52 PM by cajun_duck

I will be installing lots of moulding. I mean lots. This will probably take...

13 02-28-2012 03:40 AM
View cpd011's profile

Dust Collector / Cyclone Build

02-16-2012 02:28 PM by cpd011

Nothing too special here. I don’t post very often but I check out this ...

2 02-28-2012 01:18 AM
View nissen's profile

New motor

02-27-2012 09:58 PM by nissen

Hi everyone, Hope that someone out there can help me. I have an old 14...

2 02-27-2012 11:14 PM
View alexdom_89's profile

what is a fair price?

02-27-2012 03:36 PM by alexdom_89

so i was browsing threw my local cl and found this, http://mcallen.en.craigsl...

8 02-27-2012 10:42 PM
View Ripthorn's profile

Help me pick new bandsaw guides!

02-26-2012 10:51 PM by Ripthorn

My wife surprised me by giving me permission to spend a little bit of tax ret...

12 02-27-2012 09:48 PM
View Rob 's profile

Delta 12" Planer 22-540 knife change help

02-25-2012 04:07 AM by Rob

So I have this used planer that’s due for a knife change. I don’...

2 02-27-2012 07:30 PM
View Cornductor's profile

hitachi mv12 and inlay kits

02-27-2012 05:23 AM by Cornductor

I’ve been searching the past hr and can’t seem to find out if the...

1 02-27-2012 06:01 PM
View levans's profile

I can't figure this one out

02-26-2012 04:25 AM by levans

First things first, I’ve just joined and want to say hello to all and t...

3 02-27-2012 05:58 PM
View ChrisCrafts's profile


02-26-2012 11:54 PM by ChrisCrafts

I am hoping to find some help from someone who has expert knowledge about run...

6 02-27-2012 05:31 PM
View rut's profile

Need some help with a planer

01-25-2012 04:08 AM by rut

I have my dad’s old 6” Sears planer. I went through a setup using...

14 02-27-2012 05:28 PM
View Iggles88's profile

Table saw

02-27-2012 12:43 AM by Iggles88

Hey guys, i have had two different table saws in less then four months, the f...

19 02-27-2012 05:21 PM
View sawedoff's profile

new dust collector

02-26-2012 08:57 PM by sawedoff

I had bought a 1hp harbor freight DC last month and before even using it with...

3 02-27-2012 03:22 PM

« prev 1 ... 728 729 730 731 732 733 734 ... 1263 next »
25253 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics