Power Tools, Hardware and Accessories Forum

  • Advertise with us

Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be an overwhelming adventure, and you have some tough decisions to make. Welcome to the Woodworking Forum that allows you to seek and find essential information from other like-minded folks who have walked the same path before.

Topics Replies Last post
View patcollins's profile

Grrrrippper and old style splitter

05-14-2011 04:59 PM by patcollins

Hey everybody, I ws thinking about getting or making a Grrrriper style pushb...

4 05-15-2011 06:26 PM
View Chipy's profile

Router lifts and Hitachi M-12

04-30-2011 04:13 PM by Chipy

I have an Hitachi M12 router and I would like to use it in a router lift se...

7 05-15-2011 02:06 PM
View idunno's profile

Android / Smartphone as Metal Detector?

05-05-2011 08:14 PM by idunno

My Droid phone has a built-in magnetometer, and there are a number of “metal ...

9 05-15-2011 06:24 AM
View Brett's profile

A Stanley plane that is not on the normal lists...

05-14-2011 05:41 AM by Brett

While searching for information on Stanley Bailey 5 1/2 planes, I came across...

4 05-14-2011 09:51 PM
View Mike's profile

electric in the shop

05-14-2011 06:05 AM by Mike

So I think that we have all run out of plugs in the woodshop or just needed t...

4 05-14-2011 07:42 PM
View Brett's profile

Notches in hands saws and plane irons

05-06-2011 08:10 PM by Brett

I bought two vintage saws recently that each had three little notches cut or ...

6 05-14-2011 07:38 PM
View Kinbaum's profile

Table Saw Flatness

05-14-2011 04:30 PM by Kinbaum

I purchased a JET Pro Shop Table Saw with cast iron wings last year and for t...

3 05-14-2011 05:37 PM
View jerkylips's profile

looking for a table saw..

05-13-2011 11:27 PM by jerkylips

Hello LJ’s! I posted something similiar in a reply but I wanted to a...

5 05-14-2011 03:00 AM
View Kali2024's profile

What drill bit to use for bookcase shelf pin holes?

05-10-2011 11:00 PM by Kali2024

So apparently your typical .25” typical twist bit is a no go…so w...

14 05-14-2011 12:19 AM
View Viktor's profile

Router speed control on circular saw?

05-10-2011 07:04 PM by Viktor

1) Would a speed controller used for routers work on a circular saw? I imagin...

13 05-13-2011 08:51 PM
View zindel's profile

What to get???

05-13-2011 05:31 PM by zindel

Okay so here is the question…My birthday is coming up and people keep a...

20 05-13-2011 08:36 PM
View spunwood's profile

Important Instructions!

05-13-2011 03:05 PM by spunwood

Here is a fun Troubleshooting chart tidbit from my shop vac: Symptom ...

2 05-13-2011 03:15 PM
View TMcG's profile

Jessem Rout-R-Top

05-07-2011 01:07 AM by TMcG

Anyone have any experience with this router table top ? I bought a Rou...

6 05-13-2011 01:51 PM
View reggiek's profile

MLCS Router Motor Lift

05-12-2011 11:12 PM by reggiek

I was wondering if anyone has one of these yet? Being both a tech and tool a...

1 05-12-2011 11:25 PM
View jeth's profile

Woodriver/Bailey Chisels

05-11-2011 08:45 PM by jeth

Hello all, I’m looking at a new set of chisels. I am on a very limit...

14 05-12-2011 08:46 PM
View Bill60's profile

Advice on Delta Contractor saw

05-11-2011 06:32 AM by Bill60

Hi, I only have a benchtop Mikita table saw that is about ten years old and r...

12 05-12-2011 06:08 PM
View Brett's profile

Recommended pull saws?

05-11-2011 07:15 PM by Brett

I’ve seen books and online articles that recommend types and sizes of W...

12 05-12-2011 02:43 PM
View mpounders's profile

Router guide bushing is too long...

05-11-2011 10:15 PM by mpounders

so can I just sand it off shorter? Someone gave me a cheap Central Machinery ...

7 05-12-2011 06:15 AM
View kanihoncho's profile

Need Riser Block for 1999ish Jet JWBS-14CS Bandsaw

05-12-2011 01:55 AM by kanihoncho

I am about ready to pull the trigger on a grizzly 6” riser block, part ...

1 05-12-2011 02:14 AM
View Brett's profile

Old hand saw, sharpened too much?

05-11-2011 02:31 PM by Brett

Beginner question: I bought an old Disston D-23 hand saw for $6 at an anti...

11 05-11-2011 09:03 PM

« prev 1 ... 694 695 696 697 698 699 700 ... 1118 next »
22354 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics