LumberJocks

Power Tools, Hardware and Accessories Forum

  • Advertise with us

Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be an overwhelming adventure, and you have some tough decisions to make. Welcome to the Woodworking Forum that allows you to seek and find essential information from other like-minded folks who have walked the same path before.

Topics Replies Last post
View mariongee's profile

Need help buying a moulder

07-01-2015 02:29 PM by mariongee

Looking for advice on moulders…I am currently in the market for my firs...

0 07-01-2015 02:29 PM
View lateralus819's profile

Making router table insert for table saw?

07-01-2015 12:49 AM by lateralus819

I have a 97’ Grizzly G1023 saw with a 36” Shop fox fence. It has ...

1 07-01-2015 01:08 PM
View MrFid's profile

HELP!!! Mortiser chuck key problem.

07-03-2013 06:59 PM by MrFid

Hi all, So a few weeks ago, I bought a Delta 14-650 (type 1) hollow chisel...

10 07-01-2015 12:03 PM
View unbob's profile

Shoda Shaper-Spindle Moulder

12-06-2014 07:52 AM by unbob

I found this on CL for $700 with some cutters. It is a somewhat u...

9 07-01-2015 10:58 AM
View jvallee's profile

Delta 36-725 contractor saw questions

06-28-2015 06:20 PM by jvallee

I have purchased the Delta 36-725 and am very disappointed. Poor fitting when...

7 07-01-2015 08:08 AM
View ClammyBallz's profile

Rust Remover as low as $.25 a quart.

06-29-2015 05:53 PM by ClammyBallz

I was at Lowe’s yesterday checking out some stuff in the paint departme...

10 07-01-2015 02:38 AM
View restored's profile

Powermatic Wood Lathe Model # 90

09-13-2012 03:56 PM by restored

I just purchased a powermatic wood lathe model # 90, and have start to restor...

12 07-01-2015 02:37 AM
View Joey's profile

powermatic model 45 questions

08-19-2012 08:33 PM by Joey

I just got a vintage Powermatic model 45. I’ve Done a couple of tu...

7 07-01-2015 02:20 AM
View JCurry's profile

BEST cleaner for removing oil coating from cast iron top on new Table saw

06-29-2015 11:45 PM by JCurry

I have been reading the owners manual for a saw I purchased and that has not ...

19 06-30-2015 11:08 PM
View Joshua Oehler's profile

Rigid 13" Planer. Help before I break it with a sledge hammer!!

06-29-2015 04:59 PM by Joshua Oehler

Okay, I am getting highly irritated with this planer. Don’t get me wron...

17 06-30-2015 10:35 PM
View Trucker's profile

Should I Buy a Factory Refurbished Porter Cable Jointer?

06-30-2015 07:04 PM by Trucker

Hi Everyone,I am making the transition for working exclusively with S4S pine ...

1 06-30-2015 07:14 PM
View DKV's profile

Brad point bits

06-29-2015 11:22 PM by DKV

I should be receiving my Lee Valley 1/8” through 1/2” by 64thR...

18 06-30-2015 06:24 PM
View SuperCubber's profile

Is this motor useful for anything?

06-29-2015 03:06 AM by SuperCubber

I have two of these old circular saws that were given to me. They aren&#...

15 06-30-2015 02:27 PM
View Bertha's profile

Vintage drills of your dreams

06-19-2011 11:17 PM by Bertha

Hand drills. Augers. Bit braces. This is your new home. Show off you...

1260 06-30-2015 01:44 PM
View WoodNSawdust's profile

On a Dust Collector what about placing impeller before cyclone?

06-28-2015 09:58 PM by WoodNSawdust

From what I read adding a cyclone before the impeller decreases efficiency (c...

17 06-30-2015 10:48 AM
View Ericlee1122's profile

Is it possible to modify the motor position of Ridgid TS3560 ?

06-24-2015 04:55 PM by Ericlee1122

Is it possible to modify the motor position , show as the attached picture. ...

4 06-30-2015 09:23 AM
View Whofan's profile

New Table Saw

06-29-2015 08:55 AM by Whofan

Morning , I recently picked up a new saw . It’s a new finish and I̵...

9 06-30-2015 07:06 AM
View sbauer9's profile

Which lathe is better for my project?

06-29-2015 10:52 PM by sbauer9

Hello everyone. I am a newbie to wood turning. My main desire is turning base...

2 06-30-2015 04:01 AM
View scarpenter002's profile

Jet XACTASAW or Grizzly 691; Please help me to decide

08-30-2014 05:32 PM by scarpenter002

I am getting ready to pull the trigger on a cabinet saw, but am unsure if pay...

18 06-29-2015 11:34 PM
View mrdupfx's profile

Tips on how to do a stopped roundover?

06-29-2015 04:08 AM by mrdupfx

Hello. I am making bench seating for my kitchen (photo attached). You’...

9 06-29-2015 11:14 PM

« prev 1 2 3 4 5 6 7 ... 1091 next »
21813 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com