LumberJocks

Power Tools, Hardware and Accessories Forum

  • Advertise with us

Are you unsure of which tools, or hardware, you need, or which brands to buy? Investing in tools and hardware can be an overwhelming adventure, and you have some tough decisions to make. Welcome to the Woodworking Forum that allows you to seek and find essential information from other like-minded folks who have walked the same path before.

Topics Replies Last post
View CRDunham's profile (online now)

Sawstop 3 phase/Single Phase Swap

02-02-2017 06:46 PM by CRDunham

I’m new but there seem to be a lot of SawStop users here with nuts and ...

14 05-24-2017 10:13 PM
View Moose842's profile

Modifying a bandsaw

05-24-2017 02:52 PM by Moose842

So I’m in need if a bandsaw to use for resawing. However, for the cuts...

12 05-24-2017 09:51 PM
View vsefcik's profile

Freud glue line blade for Bosch 4100-09 table saw

06-30-2013 05:24 PM by vsefcik

I have a Bosch 4100-09 table saw and I’m considering purchasing a Freud...

10 05-24-2017 09:18 PM
View BalsaWood's profile

Dubuque Clamp Works bar clamps

05-24-2017 05:49 PM by BalsaWood

I was browsing around for some new bar clamps and noticed that the “Adj...

1 05-24-2017 07:44 PM
View andy_P's profile

Any problems with SawStop?

05-01-2017 02:35 PM by andy_P

I’m about 95% into a final decision to upgrade my 2000 Delta to a SawSt...

51 05-24-2017 07:37 PM
View kyle123's profile

Grizzly 1023 RLWX vs the other comps

05-24-2017 01:55 PM by kyle123

I know this horse has been flogged over and over for the most part, the diffe...

3 05-24-2017 05:07 PM
View JerryinCreek's profile

5/8" hole, Can I Use a Center Cut End Mill?

05-22-2017 04:15 PM by JerryinCreek

Need to cut some 5/8” holes approximately 1/16” deep into maple v...

8 05-24-2017 04:33 PM
View sreilly24590's profile

Old Powermatic 60 Jointer parts

05-18-2017 01:51 AM by sreilly24590

I’m looking for parts availability for an old 80’s Powermatic 8&#...

15 05-24-2017 01:50 PM
View SweetTea's profile

Converting 3 phase Delta UniSaw 34-450 to single phase?

05-23-2017 01:22 PM by SweetTea

Hey guys, I just picked up a Delta/Rockwell UniSaw model 34-450. The problem ...

15 05-24-2017 12:45 PM
View Mdrotar's profile

Dust collector/air filter combination question

05-22-2017 10:04 PM by Mdrotar

setting up my new shop and I’ve a question. I am adapting my single st...

13 05-24-2017 11:32 AM
View orion7144's profile

New Grizzly G0771Z

05-23-2017 11:06 PM by orion7144

I will be receiving it on Thursday and have a couple of questions. I will ...

1 05-23-2017 11:46 PM
View DonFaulk0517's profile

DeWalt DW746 Table Saw - Riving Knife Upgrade

12-24-2008 05:03 AM by DonFaulk0517

Does anyone know a way to upgrade the DeWalt DW746 10” Table Saw with a...

110 05-23-2017 10:15 PM
View steve104c's profile

Rockwell switch

05-23-2017 07:11 PM by steve104c

Bought a Rockwell 12RAS 220- 1-1/2hp single phase radial arm saw @ an estate ...

1 05-23-2017 08:45 PM
View AZWoody's profile

The Last Bandsaw I'll Need to Buy

05-21-2017 10:01 PM by AZWoody

Last month I got an email from one of the auction sites about an auction endi...

28 05-23-2017 08:39 PM
View bruc101's profile

Goodbye Delta Dust Collector

05-19-2017 04:57 PM by bruc101

I’ve had one of Delta’s Shopmaster dust collectors connected to m...

5 05-23-2017 02:29 PM
View Flacer's profile

Picking out a jointer

03-02-2017 02:45 PM by Flacer

Hi new here and looking for some advice/help on picking out a new jointer. ...

19 05-23-2017 01:09 PM
View jimmy J's profile

Daddo shim problem

05-23-2017 01:54 AM by jimmy J

In the pics, you can see each shim has been deformed around the center hole. ...

6 05-23-2017 12:38 PM
View Desert_Woodworker's profile

What is an "old" woodworking tool

05-23-2017 03:59 AM by Desert_Woodworker

In the 1970’s, I was given this single “wobble” dado washer set, from my ste...

2 05-23-2017 12:36 PM
View unclearthur's profile

Table saw arbor nut loosening with dado stack

05-12-2017 03:24 AM by unclearthur

I’ve had a couple of strange experiences with my TS; hopefully someone ...

85 05-23-2017 04:43 AM
View louroy's profile

Triton Workcenter and it's various 'modules'

05-22-2017 11:44 PM by louroy

This is just a review/rant of the Triton Workcenter, Triton Router Table modu...

0 05-22-2017 11:44 PM

1 2 3 4 ... 1308 next »
26153 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com