Woodworking Skill Share Forum

  • Advertise with us

Your woodworking skills are displayed for several lifetimes in each project. Have you had to compromise your project because you didn't know how to proceed? Relax, we all have, welcome to a Woodworking Forum that allows you to seek and find essential information from others to accomplish what your heart really had in mind.

Topics Replies Last post
View GaryK's profile

Lowe's has Irwin Quick Grip clamps 4 for $20

12-11-2009 04:54 AM by GaryK

I was just at Lowes this evening and they had their about once a year special...

27 12-14-2009 05:52 PM
View eddy's profile

convexed miter cuts ?

12-13-2009 07:12 PM by eddy

i was making some more boxes yesterday using the same sled i have been using ...

9 12-14-2009 03:59 PM
View Rileysdad's profile

Edge Banding Question

12-13-2009 10:33 PM by Rileysdad

Both Woodcraft & Rockler sell some pressure sensitive (not iron on) edge ...

6 12-14-2009 02:49 PM
View Alan S's profile

GF Gel Stain

12-14-2009 07:01 AM by Alan S

I bought gel stain to use on an oak picture frame yesterday. I had always pl...

1 12-14-2009 07:25 AM
View sikrap's profile

Advice for a Christmas gift

12-13-2009 08:55 PM by sikrap

I’m trying to buy a gift for someone that does a lot of work on a scrol...

1 12-13-2009 08:56 PM
View Travis Henley's profile

Any pointers on handcutting dovetails trying it for the first time next week

12-12-2009 10:51 PM by Travis Henley

Hey everyone next week I’m going to try to hand cut some dovetails. I ...

16 12-13-2009 05:58 PM
View Tim Dahn's profile

New Woodtreks Video

12-10-2009 07:15 PM by Tim Dahn

I noticed there was a new Video posted @ Woodtreks and thought I would pass t...

11 12-12-2009 07:20 PM
View TemplateTom's profile

Getting more from your router

12-08-2009 12:56 PM by TemplateTom Above link to a number of video...

3 12-12-2009 09:46 AM
View sikrap's profile

Benchtop advice, please

12-10-2009 05:16 PM by sikrap

I’m finally building a bench. Its just a basic bench that FWW provided ...

13 12-12-2009 09:22 AM
View lotus's profile

How do I remove this stuff?

12-11-2009 11:33 PM by lotus

Purchased a small chunk of burl that was on sale recently. It is covered wit...

6 12-12-2009 02:19 AM
View Jeison's profile

Rookie question on glue

12-10-2009 06:31 AM by Jeison

Hey all, I found a few square feet of rubber shelf liner (the good solid s...

13 12-12-2009 12:11 AM
View dbhost's profile

Joining cross grain to end grain. How to make a strong joint?

12-10-2009 06:49 PM by dbhost

I am not sure how to explain what I want to do here, but here’s the old...

11 12-11-2009 08:55 PM
View ryno101's profile

Proper use of a jointer? Help!

12-11-2009 06:32 PM by ryno101

I’ve been struggling with using my jointer since getting it, I’m ...

10 12-11-2009 08:35 PM
View EricW's profile

Is the maple from home depot hard enough for a cutting board?

12-11-2009 07:05 AM by EricW

I am going to be making a 3 inch think endgrain cutting board out of maple fo...

6 12-11-2009 08:00 PM
View ,'s profile

question about shelf pin holes

12-09-2009 07:56 AM by ,

Since we have been building kitchens, I am always looking for the best and mo...

20 12-11-2009 04:24 PM
View WoodSparky's profile

Water or Oil Paint.

12-09-2009 10:36 PM by WoodSparky

I am in the process of completing 3 doll closets. Each is 26”W 31”...

3 12-11-2009 08:44 AM
View HuntleyBill's profile

A finishing question for a new guy

12-11-2009 01:05 AM by HuntleyBill

Being new to this sight, I am already learning a lot. On past projects I have...

4 12-11-2009 06:36 AM
View WillInTheMill's profile

Paint/finish question

12-11-2009 01:10 AM by WillInTheMill

Hi everyone, I am about to complete my first side table project. I built i...

3 12-11-2009 02:44 AM
View HarleySoftailDeuce's profile

Kreg jig for building upper kitchen cabinets

12-10-2009 04:04 PM by HarleySoftailDeuce

Hello fellow Jumber Jocks,I’m about to start my upper kitchen cabinets,...

13 12-10-2009 10:23 PM
View gerrym526's profile

Wedged Through Mortise and Tenon Joint-Size of the Kerf to Accept the Wedge?

12-08-2009 12:28 AM by gerrym526

Just finishing up a pair of the James Krenov style “Smart SawhorsesR...

4 12-10-2009 06:24 PM

« prev 1 ... 454 455 456 457 458 459 460 ... 591 next »
11817 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics