Woodworking Skill Share Forum

  • Advertise with us

Your woodworking skills are displayed for several lifetimes in each project. Have you had to compromise your project because you didn't know how to proceed? Relax, we all have, welcome to a Woodworking Forum that allows you to seek and find essential information from others to accomplish what your heart really had in mind.

Topics Replies Last post
View plang's profile

Piano Hinges

04-25-2010 10:09 PM by plang

I purchased 48 inch piano hinges from Lowes. I need to cut the to 40 inches ...

7 04-26-2010 12:22 AM
View tomakazi's profile

how much?

04-23-2010 10:01 AM by tomakazi

I have the opportunity to trade work for 1300 bd ft of oak 2×4s. its a d...

2 04-24-2010 11:57 PM
View TopamaxSurvivor's profile

Oak shelf advice needed

04-21-2010 07:29 PM by TopamaxSurvivor

My wife wants a shelf to set plants on in the kitchen window. I have a piece...

10 04-24-2010 08:55 PM
View a1Jim's profile

Talking to Charles Neil ,what's next?

04-18-2010 08:59 PM by a1Jim

Hey Gang I’ve been buried with cabinet work since December no compla...

16 04-23-2010 04:28 PM
View Dyidawg's profile

Question: Is it safe to plane plywood?

04-21-2010 04:31 PM by Dyidawg

I have cut 3/4” dado in the side of a vertical piece and the 3/4”...

10 04-23-2010 12:57 PM
View siouxdawgs0409's profile

Accurate repeat bevel cuts on TS3650

04-22-2010 02:43 AM by siouxdawgs0409

Hello all. I am looking for some ideas and tips on getting accurate repeat...

8 04-22-2010 02:58 PM
View mags's profile

Not enough knowledge

04-21-2010 02:34 AM by mags

My son has a Aspen tree down on his lot. My question is Aspen any good for bu...

5 04-21-2010 03:33 PM
View KnottyWoodwork's profile

Cracks in cutting boards...

04-20-2010 10:23 PM by KnottyWoodwork

Part of last weeks woodscore, was was 4 pre laminated boards, that seemed per...

2 04-21-2010 02:33 PM
View swoper's profile

Any uses for Willow Burl

04-19-2010 10:21 PM by swoper

Hi everyone I have 2 very gnarly willows on the property, today I sliced a pi...

2 04-21-2010 03:15 AM
View sboyle's profile

Need some help and guidance

04-15-2010 10:00 PM by sboyle

Hello All, Over the last few years, I have been collecting all kinds of tools...

2 04-20-2010 10:09 PM
View JVallario's profile

Questions on convex side boxes

04-18-2010 07:11 PM by JVallario

Before I do the old try and try again routine I thought I’d seek some a...

7 04-20-2010 09:23 PM
View greenwoodbob's profile

Working with Slabs and Natural Edges

04-19-2010 10:07 PM by greenwoodbob

I have a prospective client who wants a large slab table top (about 10’...

3 04-20-2010 08:59 PM
View GeneL's profile

Moving book case

04-18-2010 07:25 PM by GeneL

I am about to start on my next project and could use a little advise. The ...

4 04-20-2010 06:49 PM
View Beginningwoodworker's profile

Niche woodworking?

04-18-2010 05:37 AM by Beginningwoodworker

Someday I would like to do woodworking full time, I am trying to get into a n...

15 04-20-2010 03:48 PM
View woodnut's profile

bandsaw tires

04-17-2010 05:29 AM by woodnut

I have a 17” bandsaw and would like to purchase the urethane tires for ...

3 04-20-2010 03:38 AM
View Bret's profile

Removing unwanted expoxy squeeze-out

04-15-2010 04:21 PM by Bret

I’m planning to stop by Woodcraft this afternoon to ask their input as ...

4 04-19-2010 11:47 PM
View Billinmich's profile

Lambs tongue

04-19-2010 07:11 PM by Billinmich

I’m building a couple of end tables and would like to add lamb tongue ...

2 04-19-2010 10:27 PM
View DonJ's profile

Piano Hinge Use

04-18-2010 03:31 AM by DonJ

I’m building one of the 3’ tall jewlery chests with the sides tha...

3 04-19-2010 09:40 PM
View RaceRed150's profile

trying to keep fresh cut silver maple from checking.

04-19-2010 03:32 PM by RaceRed150

Hi I’m new to the site and just had a large silver maple cut down on th...

1 04-19-2010 07:13 PM
View bill1352's profile

Blushing table top.

04-18-2010 02:37 AM by bill1352

I was polishing out a table top with Micro Mesh discs and the phone rang. The...

4 04-19-2010 02:41 AM

« prev 1 ... 429 430 431 432 433 434 435 ... 605 next »
12097 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics