LumberJocks

Woodworking Skill Share Forum

  • Advertise with us

Your woodworking skills are displayed for several lifetimes in each project. Have you had to compromise your project because you didn't know how to proceed? Relax, we all have, welcome to a Woodworking Forum that allows you to seek and find essential information from others to accomplish what your heart really had in mind.

Topics Replies Last post
View lotus's profile

How do I remove this stuff?

12-11-2009 11:33 PM by lotus

Purchased a small chunk of burl that was on sale recently. It is covered wit...

6 12-12-2009 02:19 AM
View Jeison's profile

Rookie question on glue

12-10-2009 06:31 AM by Jeison

Hey all, I found a few square feet of rubber shelf liner (the good solid s...

13 12-12-2009 12:11 AM
View dbhost's profile

Joining cross grain to end grain. How to make a strong joint?

12-10-2009 06:49 PM by dbhost

I am not sure how to explain what I want to do here, but here’s the old...

11 12-11-2009 08:55 PM
View ryno101's profile

Proper use of a jointer? Help!

12-11-2009 06:32 PM by ryno101

I’ve been struggling with using my jointer since getting it, I’m ...

10 12-11-2009 08:35 PM
View EricW's profile

Is the maple from home depot hard enough for a cutting board?

12-11-2009 07:05 AM by EricW

I am going to be making a 3 inch think endgrain cutting board out of maple fo...

6 12-11-2009 08:00 PM
View ,'s profile

question about shelf pin holes

12-09-2009 07:56 AM by ,

Since we have been building kitchens, I am always looking for the best and mo...

20 12-11-2009 04:24 PM
View WoodSparky's profile

Water or Oil Paint.

12-09-2009 10:36 PM by WoodSparky

I am in the process of completing 3 doll closets. Each is 26”W 31”...

3 12-11-2009 08:44 AM
View HuntleyBill's profile

A finishing question for a new guy

12-11-2009 01:05 AM by HuntleyBill

Being new to this sight, I am already learning a lot. On past projects I have...

4 12-11-2009 06:36 AM
View WillInTheMill's profile

Paint/finish question

12-11-2009 01:10 AM by WillInTheMill

Hi everyone, I am about to complete my first side table project. I built i...

3 12-11-2009 02:44 AM
View HarleySoftailDeuce's profile

Kreg jig for building upper kitchen cabinets

12-10-2009 04:04 PM by HarleySoftailDeuce

Hello fellow Jumber Jocks,I’m about to start my upper kitchen cabinets,...

13 12-10-2009 10:23 PM
View gerrym526's profile

Wedged Through Mortise and Tenon Joint-Size of the Kerf to Accept the Wedge?

12-08-2009 12:28 AM by gerrym526

Just finishing up a pair of the James Krenov style “Smart SawhorsesR...

4 12-10-2009 06:24 PM
View JACOBB's profile

Good (study) place to go for a beginner?

11-13-2009 05:36 PM by JACOBB

Hello, I took a few classes for beginners at a community wood shop near my...

17 12-10-2009 04:12 PM
View EROCK's profile

How to store veneer?

12-10-2009 03:34 AM by EROCK

Hello fellow Lumberjocks! So I just received a huge box (about 10-12 lbs) ...

2 12-10-2009 05:01 AM
View Brian Havens's profile

A question for folks who do NOT use card scrapers (or were reluctant at first)

12-03-2009 01:08 AM by Brian Havens

I have been doing some research on topics for new videos, and I may need a re...

42 12-10-2009 03:17 AM
View jim1mckenna's profile

Help with Video

12-09-2009 03:36 AM by jim1mckenna

I want to start recording stuff to post on iternet I have adobe premiere elem...

1 12-10-2009 02:40 AM
View Fister's profile

Gluing Cocobola miter cuts

12-09-2009 06:31 AM by Fister

I am making a small jewelry box out of cocobola. Here is the rub: The sides...

3 12-09-2009 04:36 PM
View Bret's profile

Preparing curly walnut & curly maple for finishing & assembly

12-09-2009 12:28 AM by Bret

I’m getting ready to assemble a box I’m building from curly maple...

2 12-09-2009 12:55 AM
View Joe's profile

Rabbet Advise

12-07-2009 06:23 PM by Joe

Greetings LJ, I’m starting on a gun cabinet for my father. The door fr...

7 12-07-2009 11:57 PM
View snowdog's profile

Nitrocellulose Lacor repair

12-06-2009 04:55 PM by snowdog

I have done a little research but need some guidance on this. My step-son tr...

5 12-07-2009 04:07 PM
View Tim Dahn's profile

Carving chisel sharpening methods

12-06-2009 08:41 PM by Tim Dahn

Hey can anyone point me towards a website that has information on how to shar...

6 12-07-2009 03:44 AM

« prev 1 ... 419 420 421 422 423 424 425 ... 556 next »
11119 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com