LumberJocks

Woodworking Skill Share Forum

  • Advertise with us

Your woodworking skills are displayed for several lifetimes in each project. Have you had to compromise your project because you didn't know how to proceed? Relax, we all have, welcome to a Woodworking Forum that allows you to seek and find essential information from others to accomplish what your heart really had in mind.

Topics Replies Last post
View Madmark2's profile

Some tools for soft woods only.

04-20-2017 10:35 AM by Madmark2

In my shop we work jatoba a lot. Not all tools that work on soft wood will wo...

0 04-20-2017 10:35 AM
View AlaskaGuy's profile

ARE TOOLS MADE OVERSEAS OF POOR QUALITY AND IF SO WHO'S TO BLAME

02-28-2017 06:41 PM by AlaskaGuy

My answer to Jim’s post. There are plenty of high quality tools avai...

28 04-20-2017 10:18 AM
View Pieter_hb's profile

Wood-resin cubus fun

04-19-2017 08:38 AM by Pieter_hb

Hi All I tried my hand for the first time on resin for wood and then made ...

2 04-19-2017 09:52 AM
View groland's profile

Grizzly G0528 Router Table question

04-07-2017 08:01 PM by groland

I just picked up a Grizzly G0528 router table, used, and have been working to...

1 04-18-2017 01:02 PM
View papadan's profile (online now)

1981....36 years is long enough between builds!

04-16-2017 01:58 PM by papadan

In 1981 I was off work for a few months because of knee surgery I couldn...

17 04-18-2017 12:56 PM
View groland's profile

Grizzly G0528 Making a Home-built Fence Share

04-18-2017 12:01 PM by groland

I am interested to hear from anyone who has built a home-made fence for this ...

0 04-18-2017 12:01 PM
View Lemongrasspicker's profile

Making a Jointer Plane (Advice/knowledge sought)

04-18-2017 07:01 AM by Lemongrasspicker

I am in need of a jointer plane in the 24” range. I have the materials ...

6 04-18-2017 10:55 AM
View jonnybrophy's profile

Feeling Discouraged

04-08-2017 05:56 PM by jonnybrophy

Hey guys,I have been trying my hand at woodworking for about 1 and a half now...

34 04-17-2017 05:40 PM
View 85GoCards's profile

Need Some Expertise and/or Tips and Tricks - Stabilizing Wood

04-08-2017 07:47 PM by 85GoCards

As the pictures show, I have some gorgeous wild olive wood in desperate need ...

4 04-16-2017 05:30 PM
View Pieter_hb's profile

Alternative creative wooden frames

04-16-2017 01:47 AM by Pieter_hb

Hi Everybody Attached are 5 frames I made from Wild Olive wood and Rhodesi...

8 04-16-2017 08:38 AM
View pontic's profile

I don't have car inshurance.........

04-12-2017 06:49 PM by pontic

But I do have a lowe’s card

13 04-15-2017 06:08 PM
View ScottKaye's profile

2 flute straight bit into endgrain

04-13-2017 08:40 AM by ScottKaye

I’m looking into using a 1/2” – 2 flute straight bit to cu...

9 04-13-2017 09:12 PM
View papadan's profile (online now)

Part #2 More than just wood

04-11-2017 11:04 PM by papadan

Finished up the sheath and display stand for my hunting knife. The stand is a...

15 04-12-2017 11:06 PM
View chef57's profile

Crosscut with new freud blade

02-05-2017 09:12 AM by chef57

Hi all, I am new to woodworking and I have just installed a new freud crosscu...

33 04-12-2017 08:31 AM
View papadan's profile (online now)

Part #1, more than just wood.

04-08-2017 07:47 PM by papadan

Scrounging around the garage and found a couple billets I made a while back. ...

29 04-11-2017 11:00 PM
View KnickKnack's profile

Jointing/Thicknessing on the router table - a new approach?

05-17-2011 09:22 AM by KnickKnack

IMPORTANT – please see safety notes by contributors below I have rece...

13 04-11-2017 10:07 PM
View jtrz's profile

How to remove a hex bolt that is jammed on an old craftsmen table saw

04-08-2017 08:58 AM by jtrz

I bought an old craftsmen 10” direct drive (model number 113.221720) a...

15 04-11-2017 06:09 PM
View fords2613's profile

Help - Miter Cuts of unknown angle

04-10-2017 06:02 AM by fords2613

Hi – I need help making miter cuts where the angle is unknown and chang...

15 04-11-2017 06:07 PM
View jtrz's profile

Advice on using strap clamps for bent lamination

04-06-2017 10:42 PM by jtrz

So, it’s been a few years since I first tried bent lamination and IR...

6 04-10-2017 09:37 PM
View Chris Cook's profile

Need expertise help

04-09-2017 09:11 AM by Chris Cook

So, I have been building these boxes for Christmas presents. This is the sec...

7 04-10-2017 04:03 PM

« prev 1 2 3 4 5 ... 577 next »
11522 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com