Woodworking Skill Share Forum

  • Advertise with us

Your woodworking skills are displayed for several lifetimes in each project. Have you had to compromise your project because you didn't know how to proceed? Relax, we all have, welcome to a Woodworking Forum that allows you to seek and find essential information from others to accomplish what your heart really had in mind.

Topics Replies Last post
View gr8outdrsmn's profile

Are there any Traditional Woodworkers among us?

12-18-2008 05:44 PM by gr8outdrsmn

I have always liked doing things the old fashioned way. I think i get it fro...

41 03-08-2015 05:00 PM
View mandatory66's profile

Shelf span with 3/4 ply

03-08-2015 04:15 AM by mandatory66

I am installing a couple of shelves in a cabinet that will have to span 38 in...

4 03-08-2015 05:29 AM
View todd4390's profile

Crosscut Sled Woes

03-06-2015 10:56 PM by todd4390

I’ve been trying to make one of these for a week now and every time I a...

16 03-08-2015 03:03 AM
View BrandonR's profile

How to make this cut?

03-07-2015 04:26 PM by BrandonR

I am working on making a large number of boxes/cradles for a client… Th...

6 03-07-2015 07:08 PM
View skatefriday's profile

Warping hardwood plywood.

03-07-2015 01:24 AM by skatefriday

So last Sunday I cut down a 3/4” maple panel. The good stuff, B1 (suff...

8 03-07-2015 03:07 PM
View Woodbridge's profile

Seeking Advice When Gluing Up A Marquetry Panel

03-07-2015 01:30 AM by Woodbridge

This week I have been working on a marquetry panel for another “Make a ...

4 03-07-2015 02:51 PM
View Acslater's profile

How do I make a clean rectangular cut out of a 2" thick board?

02-24-2015 11:15 PM by Acslater

I’m looking to run a 1” thick board with 3” width through a...

11 03-07-2015 04:50 AM
View mattme's profile

Pine dinning table project (I'm new). Started to sand but need to strip?

03-04-2015 04:03 AM by mattme

Hey all, I’ve got a dining table that is made out of pine with some ...

4 03-06-2015 01:52 AM
View Jeff_in_LSMO's profile

Help making 1x1 inch boxes with 1/8 material

03-04-2015 09:44 PM by Jeff_in_LSMO

I want to make a bunch of small 1×1 x 0.5” deep boxes, and I want ...

19 03-05-2015 05:16 PM
View mbzguy's profile

Cutting stopped slots.

03-04-2015 09:17 PM by mbzguy

So I have to cut a lot of 3/4” stopped slots in 3/8 baltic birch as sho...

6 03-05-2015 03:15 AM
View Arthouse's profile

New Altar

03-04-2015 10:39 AM by Arthouse

I have been commissioned by St Mary’s Catholic Church to build a new Al...

5 03-05-2015 02:14 AM
View BrandonR's profile

Brad Nailer vs. Pin Nailer on 1/4 material

03-04-2015 03:32 AM by BrandonR

I just got a request to make some small boxes for a client. He wants me to us...

11 03-05-2015 01:30 AM
View BrandonR's profile

Method for cutting dado on edge of board...

03-04-2015 04:25 PM by BrandonR

I need to get very then dado on the edge of some 1/4 material. The dado will ...

2 03-04-2015 05:00 PM
View Divotdog's profile

Need Advice To Fix My Mistake

03-04-2015 03:01 AM by Divotdog

Hi - I haven’t been on here for a while but I need some advice. I ma...

5 03-04-2015 04:24 PM
View bhacksaw's profile

Texturing advice

03-03-2015 07:29 PM by bhacksaw

I’m planning on building a bar with a textured look seen in the accompa...

6 03-04-2015 04:02 AM
View Tunalmelt's profile

Need Help Stabilizing Threaded Rod To Wooden Base For A Lamp

03-02-2015 04:14 PM by Tunalmelt

hello! I recently ordered

2 03-02-2015 08:39 PM
View 007alexei700's profile

My skills

03-02-2015 05:58 PM by 007alexei700

Hello everyone. I am from bangladesh and am very interested in woodworks. It ...

4 03-02-2015 08:01 PM
View marc_rosen's profile

using a pin nailer on hard maple?

03-02-2015 01:17 AM by marc_rosen

Hello Gang,(First, I plan to experiment on several pieces of scrap once I dra...

5 03-02-2015 10:49 AM
View DanielP's profile

Defining comments on Jerry's Invisible Joint project

02-27-2015 07:41 PM by DanielP

picture 1… picture 2…. I got to thinking about my correcti...

19 03-02-2015 02:02 AM
View majeagle1's profile

Maintenance of Oil Finishes

06-19-2010 09:59 PM by majeagle1

Curious about what all of you wonderful LJ’s out there recommend to you...

3 03-02-2015 12:15 AM

« prev 1 ... 7 8 9 10 11 12 13 ... 519 next »
10373 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics