LumberJocks

Joinery Forum

  • Advertise with us

Have a question? a tip/strategy to share? a challenge, perhaps? Share your "joinery" discussion here.

Topics Replies Last post
View bluekingfisher's profile

Breadboard End - Advice please

11-19-2014 08:42 AM by bluekingfisher

I intend to make a breadboard end on a panel to adorn the top of a small ward...

6 11-20-2014 08:19 AM
View Russianspy's profile

Small dips at the end of a routed edge

11-18-2014 03:02 PM by Russianspy

At the end of each pass on my router table I am getting small imperfections w...

4 11-18-2014 04:34 PM
View schu777's profile

Options for drilling a 2" hole in hard maple

11-17-2014 03:57 PM by schu777

I’m looking for options (other than a drill press) to drill a 2” ...

7 11-17-2014 06:25 PM
View zippymorocco's profile

Could you help me choose the best joint?

11-17-2014 04:01 PM by zippymorocco

Hello, This is my first post! I am hoping to find some insight. I am plann...

5 11-17-2014 05:53 PM
View Flipper01's profile

joining

11-16-2014 10:39 PM by Flipper01

Has anyone ever heard of Isoloc templates for Porter Cable instead of Leigh? ...

0 11-16-2014 10:39 PM
View jasonallen's profile

Hawk JointABILITY

11-12-2014 02:28 AM by jasonallen

Does any one know anything a bout the Hawk JointABILITY? It seems like it mi...

6 11-13-2014 03:48 AM
View ATLwoodworker's profile

Edge grain counter top

11-10-2014 09:49 PM by ATLwoodworker

I just joined Lumberjocks after having read posts for a few years. I’ve...

3 11-11-2014 12:10 AM
View Dreek's profile

Orthogonal mortises into a laminated post

11-06-2014 06:37 PM by Dreek

Hi folks, It’s my plan to build a loft bed for my son. The design i...

6 11-07-2014 10:05 PM
View dbargaehr's profile

Joining tabletop to modern legs

11-06-2014 11:12 PM by dbargaehr

Ahoy there, first-time poster and amateur in every sense of the word. Work...

3 11-07-2014 12:43 AM
View wiser1934's profile

adding a bread board end to a cutting board

11-06-2014 02:43 AM by wiser1934

i saw at some point that someone used a dowel pin(s) to attach the end on. us...

3 11-06-2014 04:59 PM
View bbasiaga's profile

Making Table legs from 4/4 Lumber question

03-02-2013 04:51 AM by bbasiaga

I’m going to make some legs that are 2.5” thick (and also 2.5R...

14 11-06-2014 01:54 PM
View blackwell's profile

Sliding dovetail raised panels

11-04-2014 06:41 PM by blackwell

I’m planning a small entry table to sit at my front door. The rough siz...

6 11-04-2014 09:47 PM
View DBrown52's profile

Joining arm rests to rear legs

11-03-2014 09:46 PM by DBrown52

So, I’ve been thinking about building an A&C rocker for some time. ...

8 11-04-2014 06:14 PM
View 1371Marine's profile

Need a little help on edge joining...It's been a while!

10-31-2014 02:01 AM by 1371Marine

I’m getting ready to build a bar top out of southern yellow pine. I am...

12 11-04-2014 10:52 AM
View patrickhosey's profile

What is this joint called part 2. Video of the build.

11-03-2014 01:49 AM by patrickhosey

http://youtu.be/ycqX5uMNQ9A I got a lot of good answers on the last po...

4 11-03-2014 04:13 PM
View Eugene's profile

Gluing Ebony

10-31-2014 06:42 PM by Eugene

I am trying to make some curved Ebony stringing 5mm square. To bend it withou...

8 11-01-2014 07:08 PM
View patrickhosey's profile

What is this joint called?

09-22-2014 11:09 PM by patrickhosey

Three-way Bridle Joint? What would happen if you googled three-way butt joint...

23 10-29-2014 11:25 PM
View fis7470's profile

mortising machine

10-27-2014 03:12 PM by fis7470

Hello, I have a powermatic mortising machine and I am having problems wi...

5 10-28-2014 02:32 PM
View johnhutchinson's profile

It's not about the nail

10-24-2014 02:24 PM by johnhutchinson

This is a MUST SEE for anyone who’s used nails in a woodworking project...

26 10-26-2014 01:15 PM
View jimmyhopps's profile

shaker panel glue order

10-24-2014 03:03 AM by jimmyhopps

I’ve got all the pieces cut for a series of 5 piece drawer fronts (rail...

5 10-24-2014 07:30 AM

1 2 3 4 ... 24 next »
475 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase