Woodturning Forum

  • Advertise with us

On the lathe, by the lathe: do you have questions? frustrations? tips? This forum is for all the woodturners out there.

Topics Replies Last post
View Karda's profile

Jam chick

10-08-2017 12:13 AM by Karda

Hi, I just got done turning a maple plate but I can’t remove the tenon....

3 10-08-2017 03:45 AM
View kmetzger's profile

Replacement velcro for sanding pads

10-06-2017 02:16 PM by kmetzger

Hello – I’m looking for an inexpensive way to replace worn out ve...

9 10-07-2017 02:04 AM
View telrite's profile

looking for help

10-05-2017 01:42 AM by telrite

Awhile back I saved a PDF on how to make the outside rounded pieces and now I...

4 10-06-2017 11:51 AM
View Nubsnstubs's profile

mounting a natural edge piece

09-18-2017 01:32 PM by Nubsnstubs

Another video on mounting using my Chuck Plate. I started with an 8” ha...

1 10-04-2017 03:16 PM
View jason1's profile

Mandrel sizing

10-03-2017 01:48 PM by jason1

Hello all, I am new to the site and have found some interesting topics on her...

2 10-04-2017 12:15 PM
View Bruyet's profile

Spruce Burl

10-02-2017 12:10 PM by Bruyet

While visiting my daughter in Duluth, MN, I spotted a relatively ...

3 10-03-2017 07:11 PM
View Karda's profile

carbide tool question

10-01-2017 02:13 AM by Karda

I made a carbide tool with a round cutter, I was wondering what are the squar...

11 10-03-2017 06:11 PM
View Madrona's profile

Jet 1840 Lathe Review - Video

10-03-2017 05:45 AM by Madrona

I’ve had my lathe for six months, now, and decided to post a video revi...

3 10-03-2017 05:19 PM
View telrite's profile

shellawax cream over stained turnings

10-01-2017 09:41 PM by telrite

I have turned a base and finial for a hollow form I am working on. They are m...

1 10-02-2017 10:32 AM
View WoodChuck84's profile

Woodriver Pen Press

10-01-2017 11:59 PM by WoodChuck84

The threaded stud broke off of the handle of my Woodriver Pen Press. Anybody...

3 10-02-2017 01:07 AM
View Jerry's profile

Seeking advice on carbide lathe tools - What's the best starter set

09-13-2017 07:52 PM by Jerry

Hey all, I’m getting ready to get some carbide bit and fabricate my own...

36 09-29-2017 02:51 AM
View Abter's profile

?? experience with Crown 24650 scraper/hollower

09-28-2017 05:10 PM by Abter

I ran across this tool, and can’t find any info on it beyond what Crown...

2 09-28-2017 07:56 PM
View telrite's profile

Long stem hollow form

09-27-2017 12:30 AM by telrite

17” tall. Curly maple and some wood I don’t know. The fellow I go...

5 09-28-2017 01:06 AM
View Karda's profile

chunk cut

08-07-2017 06:30 AM by Karda

I got my cherry chunks cut up not to blanks just to dry got mostly spindle bl...

2 09-26-2017 01:18 AM
View Karda's profile

need advice

09-18-2017 05:44 AM by Karda

I cut up a couple maple logs, the thin piece I cut for a plate tappers and i...

20 09-25-2017 08:20 PM
View Thfay's profile

Adding abrasives to wax

09-20-2017 02:40 PM by Thfay

I want to add Tripoli powder or other fine abrasive to oil and wax to make a ...

7 09-24-2017 03:01 PM
View Jack Lewis's profile

How do you calculate (Revisited) staved angles on segmented rings

09-22-2017 06:18 PM by Jack Lewis

I think the method of flat segmented rings has been solved with complete clar...

7 09-23-2017 04:45 PM
View Nubsnstubs's profile

Completing the Natural Edge Piece

09-19-2017 02:18 PM by Nubsnstubs

Another video showing 2 different jam/ jamb chuck or a plug. You pick the nam...

0 09-19-2017 02:18 PM
View Madrona's profile

Pulled From Fire?

08-26-2017 01:04 AM by Madrona

Looking through my wood pile for something to turn and found this piece that ...

8 09-18-2017 07:47 PM
View JMillerWoodworks's profile

What Type of Lathe Centers to Use

09-17-2017 01:17 AM by JMillerWoodworks

Recently my brother and I were given an old Craftsman Lathe (model no. 113.23...

4 09-17-2017 06:41 AM

« prev 1 ... 6 7 8 9 10 11 12 ... 102 next »
2035 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics