LumberJocks

Woodturning Forum

  • Advertise with us

On the lathe, by the lathe: do you have questions? frustrations? tips? This forum is for all the woodturners out there.

Topics Replies Last post
View Jack Lewis's profile

Chord chart for segment length

02-08-2018 10:34 PM by Jack Lewis

I got so tired of calculating segment length I made a spreadsheet with radius...

2 02-09-2018 03:04 PM
View BRTree's profile

Powermatic 3520B

09-02-2016 08:35 PM by BRTree

Anyone on the east coast have one—-and want to sell it? What should ...

3 02-08-2018 11:18 PM
View jimbo71's profile

Looking for a lathe - and thinking about the Nova Saturn

02-03-2018 07:46 PM by jimbo71

New here, searched under several listings and read a lot of good information....

28 02-08-2018 05:58 AM
View JMillerWoodworks's profile

Pen Turning Mandrel Question

02-08-2018 02:33 AM by JMillerWoodworks

I am new to turning pens and currently have been using a 7mm mandrel. I would...

5 02-08-2018 03:45 AM
View Madrona's profile

Que, sera, sera...

01-31-2018 03:48 AM by Madrona

It didn’t start out to be a square edge bowl and it didn’t start ...

4 02-07-2018 08:54 PM
View Karda's profile

epoxy whitens on drying

02-07-2018 01:00 AM by Karda

Hi I have a knot with a crack in it that is to big for CA so I mixed up some ...

20 02-07-2018 05:41 PM
View JerseyJoe's profile

Table Pedestal Turning

01-28-2018 08:53 PM by JerseyJoe

Hello everyone, I’m about to start a new project and I need some adv...

7 02-05-2018 09:50 PM
View chrismusaf's profile

Delta DL40 Speed Control Board Fuse

06-22-2016 08:38 PM by chrismusaf

Hi everyone, I volunteer at a wood shop on a military base. We have an ol...

10 02-04-2018 09:35 PM
View db366's profile

Minimax t124

02-04-2018 07:50 PM by db366

I am looking for someone who has or has had experience on this lathe, specifi...

2 02-04-2018 08:44 PM
View Karda's profile

glue block help

01-26-2018 01:04 AM by Karda

I want to return some bowl I first did because I can see so many things I cou...

10 02-03-2018 10:53 PM
View Clarkswoodworking's profile

Tormek 2000 any tips

02-02-2018 06:10 PM by Clarkswoodworking

Got lucky and picked upA nice tormek 2000 with ji...

4 02-03-2018 04:44 AM
View bcramer's profile

Using my lathe again after a year off

02-02-2018 12:27 AM by bcramer

I am going to start using my lathe again after about a year of being idle bec...

2 02-02-2018 02:05 AM
View thimmaker's profile

Delta 46-701

01-28-2018 03:27 AM by thimmaker

Anybody using an old Delta 46-701? and do you have any problems with it?

10 02-01-2018 03:36 PM
View BANTAR's profile

Parts for a toolkraft 711

01-31-2018 12:24 AM by BANTAR

I just got my first lathe. It’s a Toolkraft 14” model 711. I know it’s a be...

2 01-31-2018 01:02 AM
View Abter's profile

height vrs base diameter for a table lamp ??

01-30-2018 12:09 AM by Abter

{my question is about a lamp that sits on a table, not a “table lamp...

5 01-30-2018 07:59 PM
View socrbent's profile

What do you think about this special tool?

01-25-2018 07:02 PM by socrbent

The Hope treading jig suggests a relief cut at bottom of the cavity you will ...

10 01-28-2018 02:28 PM
View thimmaker's profile

Delta 46-701

01-28-2018 03:27 AM by thimmaker

Anybody using an old Delta 46-701? and do you have any problems with it?

0 01-28-2018 03:27 AM
View thimmaker's profile

Delta 46-701

01-28-2018 03:26 AM by thimmaker

Anybody using an old Delta 46-701? and do you have any problems with it?

0 01-28-2018 03:26 AM
View Etman's profile

Folksy FH-1000 wood lathe questions

01-25-2018 04:38 PM by Etman

Alright so I’ve been wanting to get a lathe, and I thought what better place ...

6 01-27-2018 05:59 PM
View stevesimon's profile

Just unboxed a new Delta 46-460 a couple of easy questions for anyone that has been there...

01-24-2018 07:31 PM by stevesimon

Hoisted the lathe up on top of my workbench and cleaned the grease off…...

6 01-24-2018 09:13 PM

« prev 1 ... 4 5 6 7 8 9 10 ... 107 next »
2124 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com