Woodturning Forum

  • Advertise with us

On the lathe, by the lathe: do you have questions? frustrations? tips? This forum is for all the woodturners out there.

Topics Replies Last post
View Jack Lewis's profile

HELP, HELP, I made a funnel

02-15-2018 06:43 PM by Jack Lewis

Went through the bottom of a hollow form segmented bowl. It is almost a sphe...

5 02-15-2018 08:30 PM
View Karda's profile

Forstner bit

02-03-2018 10:57 PM by Karda

Hi, I want to use a little larger than 2” Forstner bit to make the rece...

29 02-15-2018 06:56 PM
View 9x9's profile

Talon chuck with insert (1 1/4 x 8) cross LH/RH threaded question

02-13-2018 04:08 PM by 9x9

Looking at getting the Oneway Talon chuck with insert (1 1/4×8) cross LH...

4 02-15-2018 02:11 PM
View Emargerum's profile

Craftsman 15 inch head spindle

01-05-2017 12:34 AM by Emargerum

I have a craftsman 15 in. Lathe. Been having issues with it. The spindle has ...

6 02-15-2018 02:14 AM
View Drake32's profile

Need help identifying old tools

02-13-2018 08:17 AM by Drake32

After talking with my dad about my interest in getting into woodturning, he s...

8 02-14-2018 01:49 PM
View Davesaint's profile

Vintage/antique lathe?

02-11-2018 04:04 PM by Davesaint

I have a wood lathe that I picked up from a friend. I don’t have a mode...

13 02-14-2018 06:05 AM
View JPalumbo's profile

Walker Turner lathe restore question.

02-12-2018 02:39 PM by JPalumbo

Hi ya’ll, I have a question for you Walker Turner Lathe owners. I am in the m...

3 02-13-2018 06:05 AM
View Karda's profile

turning a spoon rest

02-08-2018 06:56 AM by Karda

I want to make a plate I am turning into a spoon rest, how would I make the c...

16 02-10-2018 05:53 PM
View Jack Lewis's profile

Just blew the head stock bearings

02-08-2018 10:40 PM by Jack Lewis

Had the lathe a little over two years. Did some hard roughing and now have a...

6 02-10-2018 02:02 PM
View Jack Lewis's profile

Chord chart for segment length

02-08-2018 10:34 PM by Jack Lewis

I got so tired of calculating segment length I made a spreadsheet with radius...

2 02-09-2018 03:04 PM
View BRTree's profile

Powermatic 3520B

09-02-2016 08:35 PM by BRTree

Anyone on the east coast have one—-and want to sell it? What should ...

3 02-08-2018 11:18 PM
View jimbo71's profile

Looking for a lathe - and thinking about the Nova Saturn

02-03-2018 07:46 PM by jimbo71

New here, searched under several listings and read a lot of good information....

28 02-08-2018 05:58 AM
View JMillerWoodworks's profile

Pen Turning Mandrel Question

02-08-2018 02:33 AM by JMillerWoodworks

I am new to turning pens and currently have been using a 7mm mandrel. I would...

5 02-08-2018 03:45 AM
View Madrona's profile

Que, sera, sera...

01-31-2018 03:48 AM by Madrona

It didn’t start out to be a square edge bowl and it didn’t start ...

4 02-07-2018 08:54 PM
View Karda's profile

epoxy whitens on drying

02-07-2018 01:00 AM by Karda

Hi I have a knot with a crack in it that is to big for CA so I mixed up some ...

20 02-07-2018 05:41 PM
View JerseyJoe's profile

Table Pedestal Turning

01-28-2018 08:53 PM by JerseyJoe

Hello everyone, I’m about to start a new project and I need some adv...

7 02-05-2018 09:50 PM
View chrismusaf's profile

Delta DL40 Speed Control Board Fuse

06-22-2016 08:38 PM by chrismusaf

Hi everyone, I volunteer at a wood shop on a military base. We have an ol...

10 02-04-2018 09:35 PM
View db366's profile

Minimax t124

02-04-2018 07:50 PM by db366

I am looking for someone who has or has had experience on this lathe, specifi...

2 02-04-2018 08:44 PM
View Karda's profile

glue block help

01-26-2018 01:04 AM by Karda

I want to return some bowl I first did because I can see so many things I cou...

10 02-03-2018 10:53 PM
View Clarkswoodworking's profile

Tormek 2000 any tips

02-02-2018 06:10 PM by Clarkswoodworking

Got lucky and picked upA nice tormek 2000 with ji...

4 02-03-2018 04:44 AM

« prev 1 2 3 4 5 6 7 ... 104 next »
2076 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics