LumberJocks

Jigs & Fixtures Forum

  • Advertise with us

Using a jig is like having a couple extra hands helping out. Show us your jigs, share your tips, strategies and, of course, questions.

Topics Replies Last post
View devann's profile

some of my jigs, fixtures, patterns etc....

03-03-2015 03:23 PM by devann

Below are pictures of some jigs I’ve made & used over the years. Ha...

13 03-11-2015 03:41 AM
View FancyShoes's profile

Cookie time!

03-09-2015 09:04 PM by FancyShoes

I picked up the Leigh dovetail jig DR4 over the weekend. Has the manual, but ...

2 03-10-2015 02:15 PM
View SkyKing's profile

What IS this thing I found in my home???

03-01-2015 08:13 PM by SkyKing

Hi, woodworking people; I just joined to try to figure out what this item is ...

34 03-08-2015 02:03 PM
View Rick1970's profile

Sealing table saw sleds and other jigs to prevent warping from moisture

02-09-2015 04:24 PM by Rick1970

For those of you who live in humid climates, do you seal, (apply some kind of...

15 03-06-2015 06:39 PM
View TheWoodenOyster's profile

Functionality of shooting boards

01-30-2015 07:00 PM by TheWoodenOyster

Hey guys, Like everyone, I’m always looking for that 90.00000 degree...

15 03-05-2015 02:15 PM
View Ramski's profile

Panel King / Exact T Guide System

09-30-2014 01:45 AM by Ramski

Hi All, I have been “snooping around” the site on and off for several year...

3 03-05-2015 04:36 AM
View BadgerJoe's profile

Where to buy a viewer/marker for fixed measurement tape?

03-03-2015 05:01 PM by BadgerJoe

Good Morning! I am looking to build a miter saw station to replace my port...

3 03-05-2015 01:32 AM
View coloradotrout's profile

3-foot shop light fixtures and bulbs

12-26-2014 12:02 AM by coloradotrout

I have not seem them widespread, but are there 3’ fixtures and bulbs av...

5 03-05-2015 01:15 AM
View 19mclaren80's profile

unusual clamps does anyone know what they are?

03-03-2015 05:02 PM by 19mclaren80

Does anyone know what this is used for, or what the proper name is? The o...

2 03-04-2015 10:57 PM
View MrRon's profile

Layout tool

12-07-2013 07:34 PM by MrRon

Here is a tool I made for laying out dimensions on sheet goods wi...

4 03-04-2015 10:33 PM
View DKV's profile

Third hand...

02-23-2015 02:03 AM by DKV

Whenever I need the end of a board held I use my scissor jack I found during ...

2 02-23-2015 02:18 AM
View deltaguy49's profile

Incra Twin Linear vs. newer LS fences?

02-16-2015 07:07 PM by deltaguy49

Hi,I am new to this forum and this is my first post. I am curious to hear op...

5 02-22-2015 05:15 PM
View cootcraig's profile (online now)

Looking for ideas for a benchtop drill press workstation fixture

02-22-2015 11:54 AM by cootcraig

I have a small Delta benchtop drill press and it works fine when I can secure...

3 02-22-2015 04:51 PM
View CharlesA's profile

New Leigh Router Table Dovetail Jig

10-29-2014 01:46 AM by CharlesA

I’ve been working at hand cutting dovetails, but this new Leigh RTJ400 ...

22 02-22-2015 01:49 AM
View C_PLUS_Woodworker's profile

Have Source For MortisePal Templates

02-21-2015 09:14 PM by C_PLUS_Woodworker

A Plastic Fabricator in SLC has indicated they would have no problem fabricat...

2 02-21-2015 09:26 PM
View Joshua Oehler's profile

Premade or from scratch workbench top?

01-23-2015 03:09 AM by Joshua Oehler

So I have been laid up with an injury for a few months now. Since I am finall...

13 02-19-2015 11:14 PM
View Kelly's profile

Shelf Pin Hole Jig

02-18-2015 06:16 PM by Kelly

As those who have dealt with it know, keeping all four sets of shelf pin hole...

4 02-19-2015 04:25 PM
View edwood1975's profile

Shelving Pin Holes

02-11-2015 05:16 PM by edwood1975

I just got the Kreg Pin hole jig and I’m wondering when the best time i...

11 02-18-2015 05:26 PM
View wjt99's profile

Jet Corner Clamp Update

02-17-2015 03:35 AM by wjt99

Jet Corner Clamps (P.N. 709055) have a problem with the polycarbonate cap tha...

2 02-17-2015 04:04 PM
View Fender's profile

Universal CNC fixture

02-08-2015 01:31 AM by Fender

Hows it going everyone? I am in the process of trying to make a universal CN...

1 02-08-2015 04:39 PM

« prev 1 2 3 4 5 6 ... 49 next »
970 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com