Jigs & Fixtures Forum

  • Advertise with us

Using a jig is like having a couple extra hands helping out. Show us your jigs, share your tips, strategies and, of course, questions.

Topics Replies Last post
View mds4752's profile

Long but narrow taper

10-15-2013 at 04:27 AM by mds4752

If you needed to put a 1/4” taper on a narrow but long board (2 1/2R...

12 10-16-2013 at 10:48 AM
View fatherofthree13's profile

crosscut sled vs upgraded fence system

10-14-2013 at 03:32 AM by fatherofthree13

I am a newb and I have been reading a lot on this site. I have a bit of a dil...

9 10-16-2013 at 07:53 AM
View Joshua Oehler's profile

Should I build something to convert this into a drum sander?

10-15-2013 at 10:30 AM by Joshua Oehler

I have this JET brushdrum sander sitting in my garage. I was wondering what y...

5 10-15-2013 at 07:59 PM
View Jeffreaux2's profile

Incra I-jig and tear out problems with walnut

10-01-2013 at 08:42 PM by Jeffreaux2

I’m using a 3/8” dado blade to cut box joints in 3/4” thick...

18 10-15-2013 at 11:02 AM
View farkit's profile

Need Advice; Miter Gauge With 2 Side Fences

10-14-2013 at 03:37 AM by farkit

I know it must have to do with angles but I have searched and cannot even fin...

2 10-14-2013 at 06:35 PM
View George_SA's profile

Home made drum sander question

01-07-2013 at 11:42 AM by George_SA

Just wondering before I make the commitment to build a home made drum sander....

21 10-13-2013 at 07:13 PM
View Eddie_T's profile

Bench Cookies

10-13-2013 at 12:42 PM by Eddie_T

While using a hole saw to make knobs for my router table I got the idea to ma...

0 10-13-2013 at 12:42 PM
View VTdscglfr's profile

bent lamination strips

10-11-2013 at 08:54 PM by VTdscglfr

Hey all, Does anyone have any ideas on using a belt sander in place of a d...

2 10-12-2013 at 09:37 AM
View WodDawg's profile

Vise Jig for Close Work

10-09-2013 at 04:05 PM by WodDawg

Ok, fellow nail benders and wood butchers. I need a sanity check here: I thin...

0 10-09-2013 at 04:05 PM
View lew's profile

Competition for Izzy

10-03-2013 at 11:06 AM by lew

Ran across this site- ...

2 10-08-2013 at 04:38 AM
View HuckD's profile

Shop made discs for PSA sandpaper

10-06-2013 at 08:11 PM by HuckD

I’ve been working on a disc sanding setup for my lathe. Almost finishe...

0 10-06-2013 at 08:11 PM
View SCOTSMAN's profile

router shopmade edge guides

10-05-2013 at 12:19 PM by SCOTSMAN

I have several routers mostly dewalt but recently I bough several makita 3612...

4 10-05-2013 at 10:30 PM
View ADHDan's profile

Homemade Grr...ripper smart hook (push pad with retractable rear cleat)

10-02-2013 at 10:39 AM by ADHDan

I recently came across this product, which looks like a great idea: http:/...

9 10-03-2013 at 01:19 PM
View Eddie_T's profile

Surface Mount Bench Vise?

10-03-2013 at 10:45 AM by Eddie_T

Does anyone watch Rough Cut Woodworking? If so do you know what bench top vi...

0 10-03-2013 at 10:45 AM
View MrRon's profile

Simple Box Joint Jig

09-30-2013 at 04:07 PM by MrRon

Here is a ¼” box joint jig that is a bit unconventional. To use:1. Attach ...

1 10-03-2013 at 05:49 AM
View DKV's profile (online now)

How do you store your clamps?

08-18-2013 at 01:10 PM by DKV

There are as many ways to store clamps as there are woodworkers. Youtube has...

68 10-02-2013 at 07:21 PM
View sandhill's profile

Mill-Route ?Question?

09-13-2013 at 07:38 PM by sandhill

I posted this in another forum in hopes of getting a lot of feed back. Does a...

4 09-30-2013 at 09:47 PM
View GerardW's profile

1 1/8" Groove Cut Jig- Need advice

09-23-2013 at 09:05 AM by GerardW

I am working on a new router table top made out of 3/4 phenolic faced ply, wh...

10 09-30-2013 at 08:15 PM
View lumer's profile

home made wood lathe chuck

09-30-2013 at 07:23 AM by lumer

has anyone ever made a homemade chuck for a wood lethe, i need to sand some b...

3 09-30-2013 at 12:59 PM
View NavalAg05's profile

Question on Porter Cable Dovetail Jig (4216)

09-27-2013 at 06:02 AM by NavalAg05

All, Just picked up a Porter Cable Dovetail Jig (4216). Havent had a chan...

2 09-27-2013 at 08:08 AM

« prev 1 ... 11 12 13 14 15 16 17 ... 41 next »
816 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

Latest Projects | Latest Blog Entries | Latest Forum Topics :: gardening showcase