LumberJocks

Jigs & Fixtures Forum

  • Advertise with us

Using a jig is like having a couple extra hands helping out. Show us your jigs, share your tips, strategies and, of course, questions.

Topics Replies Last post
View 3285jeff's profile

gifkins dovetail jigs

09-25-2014 12:50 PM by 3285jeff

has anyone here had any experience with a gifkin dovetail jig,,they seem the ...

1 03-28-2015 03:53 AM
View pintodeluxe's profile

Anyone Using a 14 Degree Bit in your P.C. 4210 / 4212 Dovetail Jig?

07-13-2012 06:14 PM by pintodeluxe

I was reading the supplementary instruction manual for the Porter Cable 4200 ...

14 03-28-2015 03:33 AM
View DavidL41's profile

What are your most used jigs?

03-26-2015 04:59 PM by DavidL41

Im a beginner and want to know what jigs are must haves. What jigs do you use...

3 03-27-2015 06:27 PM
View Straightlines's profile

MFT vs. T-slot table?

03-24-2015 05:11 PM by Straightlines

Fellow inmates, I’m trying to decide which system to go with for use w/...

10 03-26-2015 12:36 AM
View Joel_B's profile

Need opinions on Dovetail jigs

12-30-2014 09:05 PM by Joel_B

Ok so I have never made a dovetail joint but will need to for making some dra...

26 03-25-2015 08:14 PM
View Jerry's profile

Need ideas building a door/panel clamp table

01-27-2012 06:44 AM by Jerry

I want to build a clamp table. My goal is to build the table/jig about 36...

12 03-25-2015 02:46 PM
View LucasWoods's profile

Dog hole jig?

03-02-2015 02:28 AM by LucasWoods

So all I have is a 20v hand drill and I need to make some dog holes in my 2 1...

34 03-24-2015 07:02 PM
View georgechamplin's profile

Another KerfMaker variation

03-16-2015 02:42 PM by georgechamplin

I’ve been looking at many of the varieties of KerfMaker and most of...

6 03-24-2015 01:45 AM
View Richro65's profile

Ideas for miter saw fence

03-23-2015 02:35 AM by Richro65

Hey all, I just got a new DW716 miter saw to to replace my old 10” D...

1 03-23-2015 04:11 PM
View Todd Swartwood's profile

Jointer / Planer sharpening Jig

12-22-2014 11:08 PM by Todd Swartwood

I made this jig a few years ago before I bought new 15” Planer and 8...

4 03-23-2015 03:00 PM
View DKV's profile

New jig

02-15-2015 05:52 PM by DKV

Here is another use for a feather board. I needed some thin strips recently b...

6 03-23-2015 04:54 AM
View aaronacj's profile

80/20 extruded aluminum

03-19-2015 01:11 PM by aaronacj

I am sure someone has posted this before but just in case i wanted to share. ...

12 03-23-2015 03:16 AM
View Patrick's profile

Router Table Mortising Jig

01-09-2015 05:08 PM by Patrick

There has to be a way to make mortises on a router table better than just dro...

5 03-23-2015 02:16 AM
View dask's profile

DIY drill press clamp

03-15-2015 08:00 PM by dask

I’m designing a homemade drills press vise made from aluminum.I have a ...

1 03-21-2015 10:24 AM
View Ken90712's profile

Jointer/Planer sled

01-14-2012 12:50 PM by Ken90712

I saw tis article in Fine Woodworking magazine a while back. Thx to felll...

14 03-19-2015 03:12 PM
View cearka's profile

Trying to find this latch/catch or something similar

03-17-2015 04:51 PM by cearka

Hi all, new to this site. I’ve been searching around for a particular ...

4 03-17-2015 06:19 PM
View rwe2156's profile

Winding stick build

03-17-2015 01:53 AM by rwe2156

This was basically a prototype but I think its ok.I’m having troubl...

12 03-17-2015 05:50 PM
View Greg's profile

I need YOUR Ideas and Input for a custom Horizontal Drill Table design!

02-23-2015 05:55 AM by Greg

Hi all! I have been contemplating this custom boring machine for some years...

28 03-15-2015 09:55 PM
View InstantSiv's profile

Looking for a marking tool with unique specs.

03-14-2015 03:01 AM by InstantSiv

I have a part that needs pocket holes. What I do is gang them all up and mark...

4 03-14-2015 05:50 PM
View AlBThayer's profile

New Router lift with vertical and horizontal mounts

03-10-2015 04:36 PM by AlBThayer

I built a new kind of router lift and would like to show you how it works. Ve...

5 03-11-2015 11:17 PM

1 2 3 4 ... 48 next »
952 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com