LumberJocks

Double Bevel Marquetry...a Tulip of Various Woods

  • Advertise with us
Blog entry by Bob Simmons posted 07-26-2010 08:13 PM 4688 reads 4 times favorited 9 comments Add to Favorites Watch

One of the beautiful aspects of woodworking is that there are so many facets to the craft. Marquetry is one of these woodworking crafts that requires just basic woodworking tools and is well with the reach for all of us. The primary shop tools used for this wood project are the scroll saw, table saw, and the band saw. The hardwoods selected for this project came from a number of wood species that were in the scrap bin. Selected woods for this woodworking project include hickory, maple, padauk, and poplar.

Our woodworking plan starts with choosing a design for the marquetry. In this instance the tulip design for this woodworking project was derived from a picture of a tulip that was located on the internet and then printed. The wood veneers used in the marquetry are 3/32” thick and they were sliced on the band saw. A veneer of hickory was chosen as the background due to its warm colors and also because of its interesting grain pattern. The hickory veneer was then lightly sprayed with an adhesive and the printed tulip picture was then pressed onto it. The picture of the tulip becomes an outline for making the appropriate cuts on the scroll saw with its table set to six degrees. One might wonder “why is the scroll saw table is set at an angle of six degrees?” The reason is because we will be cutting through a taped packet consisting of two layers of veneer at one time and the angle will compensate for the saw kerf of the scroll saw blade. Note: 1.) Select a thin, fine scroll saw blade. 2.) Select a drill bit that is equal to the scroll saw blade. 3.) Use masking or blue tape to secure the packet of veneer layers to be cut. 4.) Drill an entry hole at a 6 degree angle to feed the scroll saw blade through the veneer packet.

So, what happens to the two layers of veneer being cut? Good question! One layer (hickory…the background veneer) becomes waste and the new veneer layer is then nestled into the angled cut of the hickory background piece. Remember, both veneers are being cut at the six degree angle at the same time so the infill piece will fit right into the area just removed. Once we have a good fit it is then time to apply a small amount of glue to the mating parts. We’ll use Titebond II yellow glue and then apply dampened veneer tape on the back side opposite the picture to secure the placement of the new inlay. Give it a little time to set up and then we are ready to cut another section following the glued picture of the tulip as our guide. Be selective of the choice of woods in order to “paint your picture.” The wood colors and grains will all contribute to the finished product.

As we go about the process of cutting, fitting, and gluing parts in place at the workbench you may wonder how it will look when completed because at this stage it can appear “rough.” There’s still paper on the surface and glue as well. Don’t worry and just keep pushing through because it will all clean up. Once all the parts are in place and the glue has set it’s time to prepare for the finish. Use a freshly sharpened card scraper to smooth the surface as it will give you a nicely planed surface. Sure, sandpaper can be used, however use caution as some exotic woods can bleed into other woods when sanding.

When the marquetry and the scraping is completed it’s time to frame the project just as you would a picture frame. It’s is a good idea to employ a sanding sealer such as Sealcoat to seal the surface of the veneers. Again use caution while wiping on the sealer to avoid any bleeding if using exotic woods. Then it’s a matter of choosing the wood finish of your choice.

Keep in mind that marquetry can be used in a variety of ways. For instance, a woodworker may employ marquetry in furniture pieces like as a desk or table top. Perhaps you’ve even seen marquetry applied to the face of cabinet doors. Let your imagination guide you along the way for your own woodworking projects and you’ll discover that it’s a great way to enjoy your time in the woodworking shop.

For more information on marquetry…...

Silas Kopf is a master of marquetry. Perhaps you are familiar with his work.

A few years ago Neil Lamens of Furnitology did a wonderful interview with Silas Kopf.

So, if you would like to get started in double bevel marquetry simply cut a few veneers and just practice on them for a while. Get the feel of cutting on an angle at the scroll saw. Remember,it’s normal to break a few blades and have some mistakes in the beginning. Accept that and move forward. Before long you’ll get the hang of it and you’ll be creating with confidence. Enjoy the process of double bevel marquetry!

visit…www.TheApprenticeandTheJourneyman.com

….................Learn more, Experience more!

-- Bob Simmons, Las Vegas, NV, http://TheApprenticeandTheJourneyman.com



9 comments so far

View Bob Simmons's profile

Bob Simmons

505 posts in 1665 days


#1 posted 07-26-2010 10:58 PM

Note:

Add a backer veneer of similar density to the face veneer. Glue the two veneers together for stability and to minimize wood movement.

-- Bob Simmons, Las Vegas, NV, http://TheApprenticeandTheJourneyman.com

View Joe Lyddon's profile

Joe Lyddon

7710 posts in 2703 days


#2 posted 07-27-2010 05:29 AM

He makes that Marquetry look so simple doesn’t he?

Of course… ANYTHING is simple if you know how to do it!

I could just stand on the end of the low-board in a swimming pool and do a 1 1/2… Really simple…
Didn’t even really have to think about it… I just DID it…. Simple… :) :)

... it’s all in how you LOOK at it…

If we LEARN how to do something, it no longer becomes HARD… but, SIMPLE… Really! :)

Just the way he swings that stuff around on the scroll saw boggles my mind… Simple… sure….
... yeah, I suppose so… if you knew how to do it… :)

-- Have Fun! Joe Lyddon - Alta Loma, CA USA - Home: http://www.WoodworkStuff.net ... My Small Gallery: http://www.ncwoodworker.net/pp/showgallery.php?ppuser=1389&cat=500"

View Bob Simmons's profile

Bob Simmons

505 posts in 1665 days


#3 posted 07-27-2010 05:40 AM

Joe…Silas definitely knows what he’s doing. He’s probably performed Marquetry in his sleep numerous times. There’s something to be said about having knowledge and skills. You’ve got to admire someone who can make it look “simple.”

-- Bob Simmons, Las Vegas, NV, http://TheApprenticeandTheJourneyman.com

View ChuckV's profile

ChuckV

2417 posts in 2178 days


#4 posted 07-27-2010 07:41 PM

I recently watched a video by Silas. He is an amazing woodworker. When he is cutting the pieces on his electric scroll saw, you would think that the video is being fast-forwarded. And, he is not cutting at a bevel – instead he is cutting 10 to 12 identical pieces at once. And then everything fits together perfectly.

-- “That it will never come again / Is what makes life so sweet. ” ― Emily Dickinson

View Joe Lyddon's profile

Joe Lyddon

7710 posts in 2703 days


#5 posted 07-27-2010 07:48 PM

Chuck, do you have a link to it?
Are you sure he didn’t cut at an angle?
I’d like to SEE that!

-- Have Fun! Joe Lyddon - Alta Loma, CA USA - Home: http://www.WoodworkStuff.net ... My Small Gallery: http://www.ncwoodworker.net/pp/showgallery.php?ppuser=1389&cat=500"

View Bob Simmons's profile

Bob Simmons

505 posts in 1665 days


#6 posted 07-27-2010 08:17 PM

Chuck…The technique Silas Kopf used when cutting numerous identical pieces without a bevel is called “Boulle Marquetry.” It is a technique from 17th century France.

Joe… here’s a link...

-- Bob Simmons, Las Vegas, NV, http://TheApprenticeandTheJourneyman.com

View ChuckV's profile

ChuckV

2417 posts in 2178 days


#7 posted 07-27-2010 08:20 PM

Joe - This was an actual video that we saw while I was taking an inlay class at NBSS. I believe that Silas refers to this as “packet sawing”. In addition to using the scroll saw, he uses a chevalet.

Edit - Thanks Bob. It looks like I was confusing different techniques.

-- “That it will never come again / Is what makes life so sweet. ” ― Emily Dickinson

View Bob Simmons's profile

Bob Simmons

505 posts in 1665 days


#8 posted 07-27-2010 08:31 PM

Chuck…

and Joe…Here is a link to “Part 2 of “Boulle Marquetry” by Silas Kopf.

-- Bob Simmons, Las Vegas, NV, http://TheApprenticeandTheJourneyman.com

View Joe Lyddon's profile

Joe Lyddon

7710 posts in 2703 days


#9 posted 07-27-2010 09:11 PM

Bob, thank you for those two links! I remember seeing those some time ago & forgot’em.

Incidentally, when I clicked “Add to Favorites”, I am getting a crazy ERROR… Does anyone get an error?
Just curious… I reported to FWW… Just wondered if it’s just ME or not… :)
(I am a member of their Online Subscription)

-- Have Fun! Joe Lyddon - Alta Loma, CA USA - Home: http://www.WoodworkStuff.net ... My Small Gallery: http://www.ncwoodworker.net/pp/showgallery.php?ppuser=1389&cat=500"

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase