LumberJocks

How to make Bandings for Wood Inlay #2: .

  • Advertise with us
Blog entry by Bob Simmons posted 1372 days ago 1951 reads 5 times favorited 6 comments Add to Favorites Watch
« Part 1: 1 Part 2 of How to make Bandings for Wood Inlay series no next part

Once the banding segments are organized we can now focus on creating the interior design. We’ll need a few outer rippings that will sandwich the segments together and keep them in alignment. You’ll notice in the picture that the outer hardwoods are walnut and maple glued together. In this case the walnut will be on the inside with the maple on the outside. The reason for this is to create contrasting colors within the banding and also with the mahogany picture frames that will be inlaid.

Here you can see the completed bandings as they appear after gluing. 1.) Notice how the triangular segments nestle and align with one another. 2.) Also, take a close look at how the maple, walnut, and cherry contrast one another within the pattern’s design. 3.) The length of the banding is a greater than the longer side of the picture frame to be inlaid. This means a full banding length can be inlaid into the frame which eliminates smaller banding pieces being fit and glued. 4.) Two for the price of one…The two bandings pictured are of similar design, however their interior designs have opposite color combinations. (Remember that we organized the segments into two separate piles in Part 1.)

The block plane has jointed one side of the banding being held in the bench vise and now the inlay designs are clearly revealed.

The two bandings pictured are a result of our work in this tutorial. Each inlay banding shown above will be more than enough for a picture frame.

The first banding pattern has been ripped on the bandsaw and we have (6) bandings of 1/8” thickness. The second banding pattern will produce the same.

A simple mitre jig clamped to the workbench and a fine toothed dovetail saw are all that are needed to cut mitres for our woodworking project. You will notice in the companion video, How to install Wood Inlay that a sanding block is used to trim the bandings for proper fit. The sanding block is simply a fine grit sanding belt from a belt sander tightly wrapped around a block of wood.

Now it’s just a matter of trimming and fitting the inlay into the project. Note: When sanding the finished project remember that the banding is fairly thin and that the wood veneer can quickly disappear.

Once you acquire the skill of creating bandings for wood inlay you’ll more than likely develop a desire to create more banding designs. You’ll likely find yourself making “wood jewelry” in your woodworking shop. Moreover, if you are a woodworker like me you’ll soon have a family of inlaid frames on your walls as well. Good luck with your inlay and fine woodworking projects and be sure to let me know if you have any questions. I hope you enjoyed this inlay how to and if you have any questions please let me know. Thanks for viewing!

-- Bob Simmons, Las Vegas, NV, http://TheApprenticeandTheJourneyman.com



6 comments so far

View Joe Lyddon's profile

Joe Lyddon

7454 posts in 2557 days


#1 posted 1372 days ago

Very GOOD!

Limited only by one’s imagination…

Seeing the band saw setup to cut thin strips reminded me of a cool jig to allow the blade guide to be lowered closer to the wood being cut… Take an “L” strip, clamp it to your fence, move the fence (and clamped “L” strip) for 1/8” strip, and make your cuts using the Right part of the “L” as the new fence… The bearing, etc. will be out of the way of the Vertical part of the “L” as a result of having the Lower Right section of the “L” being wide enough to the space of the Bearings, etc. Works slicker than you know what!

-- Have Fun! Joe Lyddon - Alta Loma, CA USA - Home: http://www.WoodworkStuff.net ... My Small Gallery: http://www.ncwoodworker.net/pp/showgallery.php?ppuser=1389&cat=500"

View Bob Simmons's profile

Bob Simmons

505 posts in 1519 days


#2 posted 1372 days ago

Joe…That’s a great idea and thanks for sharing. I see what you mean.

-- Bob Simmons, Las Vegas, NV, http://TheApprenticeandTheJourneyman.com

View Joe Lyddon's profile

Joe Lyddon

7454 posts in 2557 days


#3 posted 1372 days ago

Bob, thought you’d like it…

Keep up the good stuff!! :)

-- Have Fun! Joe Lyddon - Alta Loma, CA USA - Home: http://www.WoodworkStuff.net ... My Small Gallery: http://www.ncwoodworker.net/pp/showgallery.php?ppuser=1389&cat=500"

View TopamaxSurvivor's profile

TopamaxSurvivor

14416 posts in 2181 days


#4 posted 1372 days ago

Looks like a good tutorial. thanks,

-- "some old things are lovely, warm still with life ... of the forgotten men who made them." - D.H. Lawrence

View scrappy's profile

scrappy

3505 posts in 1935 days


#5 posted 1372 days ago

Thanks for the great tutorial. Looking forward to giving it a try.

Scrappy

-- Scrap Wood's the best...the projects are smaller, and so is the mess!

View Bob Simmons's profile

Bob Simmons

505 posts in 1519 days


#6 posted 1372 days ago

Joe…Appreciate it. Will do!

TS…Thanks very much. You’re welcome anytime.

Scrappy…You very welcome. It works well with scrap woods too.

-- Bob Simmons, Las Vegas, NV, http://TheApprenticeandTheJourneyman.com

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase