LumberJocks Woodworking Forum banner

Modifying the shop and tools to fit the wheelchairworker......#1

6K views 30 replies 11 participants last post by  lilredweldingrod 
#1 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
 

Attachments

See less See more
14
#2 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Keep em coming! I love seeing how people use creative solutions to various issues…. This is cool stuff.
 

Attachments

#3 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Rand, you're really moving right along!

It's always nice when a plan comes together…

You remind me of "The A Team".... click… click… click… click… bang bang bang…
Thank you mam…
 

Attachments

#4 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Thanx guys. I also took the Ridgid CSMS and mobile base down back to the ocean container because all I do is roll it out, roll it back in. I almost never use it. I can do just about anything on the table saw that I can do on it, so it is now for sale.
 

Attachments

#5 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
looks good
 

Attachments

#6 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Regarding 220 volt plugs: Since you are probably only using one machine at a time on the 220 circuit, you can daisy chain other 220V plugs so that you have other places to plug in. Just hook into the current 220 box at the receptacle, or with wire nuts. When I put in 220 on my central pillar, I put a plug in each of the 4 sides. My 220 dust collector is on its own circuit from a different panel. My RAS and TS are plugged into two of the plugs, and the others are for future needs.

This should prove to be a real resource for other handicapped folks, good blog Rand.
 

Attachments

#7 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
thank´s for taking the time to do this Rand
you deffently can show us a thing or two…. wait you already have done the first
so let us set the no. high ….. to a niice round one ….. 100 is a nice no. ..... right :)
rock for us Rand

take care
Dennis
 

Attachments

#8 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
This is great Rand
Seeing this again made me feel like I should try and do somthing to help our good friends in wheel chairs so I sent this e mail to Grizzly tools. If you agree please send your own e mail and let's see if can help folks that are in those wheel chairs . They deserve having good tools too.

My e mail

Hi Grizzly folks
I'm very active on Lumberjocks.com there are close to 30,000 members and I'm the #1 commenter on this forum.
This post shows a need that should be addressed by a manufacturer ,it would help lot's of folks and be great press if you made a saw for folks in wheel chairs. I have been a big fan of grizzly tools and always tell folks on line to buy grizzly tools even over company names like Laguna, Delta, Jet, and Powermatic. Please consider this idea I know there are many out there that could use your help .
http://lumberjocks.com/lilredweldingrod/blog/23489

Thank you
Jim Brokenbourgh
Artistic wood studio

Here's their e mail address

csr@grizzly.com
 

Attachments

#9 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Great job.
 

Attachments

#10 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Thanx, guys.
Jim, I'm still in limbo as to the ownership of the house, so I'm just doing the minimum electrical for what I need to have shop time.
Jim, thanx for the note to Grizzly. It would be nice for them to consider a line of tools for the wheelchair bound woodworker. It would also be nice for them to add helpful hints to their planning site for shops. There are a lot to things that we deal with everyday that any one else able to walk would never even think of.

Example: Just to turn around 360 degrees empty handed, you can do this in approximately 1 square foot of floor space. In a manual wheel chair this same action takes 16 square feet. That is 4 feet by 4 feet. If you look at the second and third photos of this thread, you will see the wide aisle way that it take s for me to just move me and a piece of wood from the lumber rack to the saw.

There are lots of little things like that, that have to be taken into consideration when laying out a shop for a wheelchair woodworker. Heck, I'm still learning too because I'm still thinking as if I were ambulatory. lol
This is the reason for moving and trying everything in different ways in the shop.

Enjoy the blog and if you have an idea to add , please do. "Just as steel sharpens steel, so the face of one man sharpens the face of another." And Lord knows I am learning as I go along.
 

Attachments

#11 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
hey there buddy..its looking great…nothing like feeling at ease with your shop, you have done a great job and im glad its coming all together…im just waiting to see the new grizzly planer…i think a 24 incher would be good..dont let us down now..you have started out right with the table saw…what follows next is …..........keep it going…grizz
 

Attachments

#12 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Sorry Grizz. You are going to have to settle for the 12 1/2 inch Grizz planner. lol I keep it hid under the bench on the wall.The next will probably be a Grizzly drum sander, but that is a ways off.
 

Attachments

#13 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
That I understand. If you ever had the need, you could make the equivalent of a 220 extensions cord, but if you have a working solution, bide your time till and if you have clear title.

On call this weekend, sometimes I can get in a lot of shop time, other times not. Usually I am up here a lot because I can interrupt what I am typing, not so easy to interrupt finishing, or processes that get me covered in dust…...........
 

Attachments

#14 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Today was a great day here in the windy old desert. The 4 1/2Ă—2 1/2 inch reducer bushing came and the Starrett stick on tape came . Every thing is complete on the the new Grizzly. Now is the time to run every thing through the shake down cruise. lol Watch for a couple of projects in the near future.
My Marine is here for the long weekend, my youngest son is here, and two of my daughters.Having a very good visit with my family. It just don't get no better than this. lol
I hope this finds all LJ's in as great of a mood as I am in. Have a great weekend and enjoy yourselves. Rand
 

Attachments

#15 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
have A great sunday Rand and enjoy it :)

Dennis
 

Attachments

#16 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Thanx Dennis, and you and Silke have a great weekend too.
We have 5 out of 9 kids here for the weekend, so things are Goooooood. lol
And now that I can close the garage door, this cold wind will not keep me out of the shop.
And last night while puttering around in the shop, I found the misplaced Tasmanian Myrtle. he he
Picking colors for my first cutting board.
 

Attachments

#17 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
puttering with myrtle and dana
hope maddie is busy with the kids
or you may be making bread boards for months
24/7
 

Attachments

#18 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
that´s good news :) looking forward to see the first project from that saw :)
a good weekend …....... well thats depend how you look at it ….. home alone no females in the house
the most of the time had to start this morning by breaking into the washingmaschine
to get wet clothe out …. becourse I wuold try to be nice to the boss and do the loundry
when she was out of town ….........but with my usely luck I managed to breake the handle
on the door inside the mechanisme :-( .... :) well after I got it open and the front part of the door
taken of I have been able to use it all day ….. trying very hard to destroying the clothe as much as possiple
before she got home …. then she can learn it … not to leave me with out a beautyfull babysitter .. LOL

take care
Dennis
 

Attachments

#19 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Hope your mood makes up for mine, Rand…......on call, nobody home except Kermit and me. Sherie usually tries to disappear when I am on call…....work sours me on anything else. But then, it has been relatively quiet, and I have been getting in a lot of shop time. It would be better if I didn't have this crummy cold still hanging on.

On the bright side, next weekend is my birthday. My brother-in-law from Dallas is coming up, it is his birthday about the same time. I will be 70, and he will be 50, so it is a special event. The actual celebration for me will be in November with a monster family get together.

Dennis, I love that stategic thinking…..........(-:
 

Attachments

#20 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Jim, sorry that being on call is such a drag for you. I loved it. Got me away form the ex. lol That woman should have been a prize fighter. lol
But on the bright side, SHOP TIME!!! Get in the zone today Jim. lol Their not going to call. There are no pregers in Anchorage this weekend. They all went to the lower 48 for the holiday. Gotta think positive here Bro. lol
I only hope you are having as great a time as I am, except for this cold wind you just seem to have to send here. lol
but I have my ace in the hole. Now I can cut wood with the door shut, so there. I foiled you again. lol
 

Attachments

#21 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
congrat´s with the oncoming event Jim :)
and enjoy the weekend too

well maybee a smart thinking moove to try to be nice … but now I´m affraid it will backfire
when she see the maschine tomorrow …. maybee she will calm down when I tell her the sparepart
is already ordred and will be send tommorow …. should be here thirsday or wedensday latest

Dennis
 

Attachments

#22 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
This post makes me HAPPY. Not reveling in my relative health, but admiring a MAN for making things work. I've never hit a woman, Red, but I've met a few that have hit me. My shop's ground level, should you choose to visit:) Jim, I'm on call right now, too, and I feel your pain. I tell my dog when I leave in the morning, "Daddy's got to go make the kibble". It puts it all in perspective. That &((& dog and his expensive kibble;)
 

Attachments

#23 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Jim take the next flight down to him and locked that door
so he has to sweatt when the heat is back …. LOL that wuold teach him
not to brag so much …. LOL

gladyou can see the humor Rand in a cold wind now you have you new toy behind door

here it has been windy darkgrey clouded allover with rain in them the hole weekend :-(
not my kind of late spring

Dennis
 

Attachments

#24 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Al,
Yeah, I'm with you on the hitting women. In my family that is the biggest no no of all. But when I used to tell people that I was a battered husband, they would look at all 6'4" 300 pounds and look at her at 5'2" 120 pounds and roll on the floor. No win situation. My divorce was the best thing to happen for me.
She was here last month visiting our daughter that lives next door. Her husband, Ben, said, "I've only been married to her for 6 years, how do you stand it for 22?" I just reminded him that the two between died and she took their money and left the kids high and dry. So he's been warned. lol
Have you detuned the finger muscle that was breaking all the clamps? lol

Denis.
You need to be gentle with Momma's machinery. Wrecking the washer is a good way to get knuckle bumps all over your head. Now maybe we need to modify her machine to do double duty as a washer and a table saw…...But I don't know how well the saw will work with the blade changing directions and running backward though. hummmmm
Kickback vs a smackdown….
 

Attachments

#25 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Al, It's easy to see who wears the pants in your family, all four legs….lol
 

Attachments

#26 ·
Modifying the shop and tools to fit the wheelchairworker......#1

Now that I have got the new saw pretty much dialed in, I'm ready to tackle the remainder of the power tools and arrange the shop for maximum ease in operation.
Wood Table Cabinetry Hardwood Machine

This is the old saw and out feed table that I started with on my woodworking journey. As you can see, it takes up a lot of space in my cramped shop. With the saw stationed here I just barely could close the door.
Wood Floor Flooring Gas Machine

I recently bought a new Grizzly G0690 cabinet saw and lowered it to meet my requirements for comfort, safety and ease of operation.
Shelf Table Computer desk Shelving Cabinetry

I used to store the shaper/router and the bandsaw here in front of the lumber rack. They were always in the way and to be used I had to roll them out on the drive way. I won't even discuss the pain to get to a piece of wood.
Tire Vehicle Motor vehicle Automotive tire Sky

As you can see, this was the normal operation for work in my shop. During bad weather, I was only able the aggravate lumberjocks via computer as I could not work in the shop.Soooo…..
Table Building Wood Flooring Machine

I lowered the shaper/router 5 inches and dropped the bandsaw a tiny bit more to be my new out feed table.
Sky Wood Gas Luggage and bags Automotive exterior

And since both the band saw and the shaper/router have cast iron tops, when I lowered them,I made sure nothing would interfere with the miter slots.
Wood Workbench Flooring Machine tool Machine

With the bandsaw on the left side, there were just to many problems. The main problem is when doing sheet goods, the distance needed on the left side of the table saw varies too much. But I need the band saw here because of the 220v plug.
So, I swapped places with the shaper/router and the band saw. Now with the band saw here, I have the 220v plug, the shaper/router is much more handy and requires much less moving when being used for an out feed table. And when needed, I just pull it out like a drawer and get the clearance needed for rails and stiles etc.
The band saw almost never will need to be moved as the blade is out of the way of the out feed boards,and It will only need to be relocated is I need to cut long material. I will need to move it to drag out the sheet goods stored behind it.

This series will be an on going blog as I rearrange things for ease of operation and safety for me and any others using my shop.
Enjoy and any and all comments pro or con are appreciated.

PS..Remember, if it isn't a comfortable shop, it isn't a safe shop, especially for the disabled.
Could you say "no" to this, Red?

Carnivore Fawn Grass Plant Companion dog
 

Attachments

This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top