LumberJocks Woodworking Forum banner

Vintage Craftsman 306.9121 planer restoration

38K views 95 replies 32 participants last post by  donwilwol 
#1 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
 

Attachments

See less See more
20
#27 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
next question not the planer but a motor question my jointer motor crapped out luckily i have another and i wired up just fine but no matter wich way i wire it the thing spins in reverse ? i thought as long as yopu swapped leads the motor would spin the other way ? are some motors one direction only ? i have pictures to post unfortunately the motor is all painted over so no help there and so is the electrical connection cover both sides
 

Attachments

#28 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
First, I'm no electrical expert. But from my understanding not all motors are reversible. On the motor you listed before you'd switch the the red and black clipped leads as the diagram suggest. If the motor doesn't have similar leads it may not be reversible.
 

Attachments

#29 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
well don you seem to have more knowledge than I do . it may just be a one direction only i always thought if you switched the poles the motor would reverse itself but i may have to find another motor. this one was a yard sale special i found for like 10 bucks.
 

Attachments

#30 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
Think about it. If that would work, you'd just need to flip the 110 plug over.
 

Attachments

#31 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
true , ive seen it done before but that was at work where all pumps run on 220 maybe that was why
 

Attachments

#32 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
Off to a good start, Don : ) Congrats on your find . Good thing you have the skills to trouble shoot and fix as necessary.
 

Attachments

#33 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
I have a question and two things. First I was giving a craftsman planer very similar to this one. Every time I plug it in it throws the breaker switch? Any ideas? Also how do you remove the blades? I'm very new to this stuff and need all the help I can get. Thank you!
 

Attachments

#34 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
I'm not sure about the breaker, but I'd say you've got a short in the system.

As for removing the blades, loosen the set screws, drive the aluminum retainers down with a large punch, and carefully pry them out.
 

Attachments

#35 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
Thank you Don!
 

Attachments

#36 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
So I got the blades off but forgot to look at which way I put them back on. Is the sharpe point of the blade towards you or away from you?? like / or \ ??
 

Attachments

#37 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
Amber Gold Wood Tints and shades Rectangle


Front = infeed
 

Attachments

#38 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
Thanks for all this great information. Very helpful.

I have found a BelSaw 9123 on CraigsList. The beast is in working condition and looks pretty good. Probably could use a tune-up. Anyone want to make a suggestion for a fair price? I'll post a pic tomorrow.
 

Attachments

#39 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
As long as it doesn't scratch like a kitten then your good to go.LOL
I love bringing things back to new or better.The spindle moulder would not be allowed here with the safety regs I would transfer it to a bobbin sander or something else.I have heard of too many very serious injuries with spindle moulders and personally would never use one without power feed,But then I have parkinsons problems. Alistair
 

Attachments

#40 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
Thanks for all this great information. Very helpful.

I have found a BelSaw 9123 on CraigsList. The beast is in working condition and looks pretty good. Probably could use a tune-up. Anyone want to make a suggestion for a fair price? I ll post a pic tomorrow.

- JebStuart
Jeb, I missed this, sorry. Not that I'd know a value anyhow. Did you end up with it?
 

Attachments

#41 ·
Planer restoration. The beginning.

So I won a planer on ebay for $39. I bid the starting bid never expecting to win. I figured for $39, the 3hp electric motor would cover it. This was the only picture supplied.

Automotive tire Motor vehicle Vehicle Gas Automotive wheel system


Last weekend I drove to pick it up. http://lumberjocks.com/topics/39731

Once home I gave it a systems check. Does it work? The description said "In working condition", but what exactly did that mean.
Since the motor was not attached, I rewired it for 110V just to test it (will be put back to 220v for regular use). Plugged it in and it purred like a kitten.

I could see the bladed needed sharpening but wanted to make sure I could buy the parts that were needed. Doing some research I found that according to vintagemachinery.org the 306 in the serial number meant it was a Foley Belsaw, or now just Belsaw.

Font Rectangle Metal Number Nameplate


I called the number on belsaw.com and talked to someone very helpful. The Belsaw #9103 was branded under a lot of different names and numbers, the guy told me if it looks the same, it probably is the same. He admitted through company splits, a lot of the information was lost.

Typewriter Office equipment Sewing machine Wood Cylinder


So other models seem to be
Craftsman 9123
Belsaw 910
Belsaw 9103

With optional components, this can become a molding machine as well.

Some other helkpful links were
http://vintagemachinery.org/Craftsman/manufacturers.aspx?sort=1

http://vintagemachinery.org/photoindex/detail.aspx?id=8872
http://www.belsaw.com/9103pl.html

Most parts are the same as 9103
http://www.belsaw.com/index.html

He also said a lot of the parts like the rollers and primary drive components are still in use on their models today.

He also gave me a list of common failures for the machine. He said sprocket #37 is the one that seems to wear the quickest. He also said another common problem is teeth missing on the raise assembly sprockets. After knowing I could get parts I turned my attention to the machine. I looked over all of the bushings and rollers. They look sound and I could not find any worn parts. This machine didn't seem to have any of the above mentioned problems.

Next I cut some angle iron for motor mounts, made a new platform out of doubled 3/4" plywood and clamped it down, measured for a v-belt and ran to the parts store to pick up a new v-belt. They only had one, the other is on order.

Wood Gas Door Concrete Composite material


Wood Automotive tire Stairs Brickwork Brick


Next I jerry rigged an extension cord and plugged it in. A few expected rattles, but nothing unfixable came from the sounds.

The blades were in dire need of sharpening. I took out my trusty makita horizontal grinder and sharpened the blades. While they were out I gave the cutter head a good scrubbing. According to the manual, you just loosen the set screws and tap down on the retainers. This proved to be true and the blades were removed with out any incident. A thorough cleaning of all parts before re-installation was performed as well.

Light Gas Cylinder Metal Office equipment


Wood Bottle Bumper Gas Hardwood


The blades then went back in.

Bumper Gas Wood Machine Metal


Next I cleaned the bed, wire brushed, sanded, and de-rusted until it looked respectable again.

With the motor still clamped in place, I ran a couple of board through it. How sweet. Compared to my Ryobi lunchbox this is going to be a charm.

The original motor mounts were held on with J hooks. I decided to make a few metal clamps. These will be painted.

Road surface Motor vehicle Automotive tire Asphalt Bumper


The some dust collection. This isn't complete, but you may be able to see where its headed.

Wood Table Gas Machine Wood stain


So last night I picked up some hinges for the dust collection, bolts for everything, primer and paint, a length of 10-2 power cord, switch, box and plug and a few other misc parts needed.

Next up will be some painting. The closest color I could find was a dark grey machine paint. I don't plane to totally strip it and paint everything, so I'll deal with the variation. I'll work on the dust collection.

So that's it for part one. Thanks for looking. I hope to see you on the next installment.
Are there any one out there that has parts for a belsaw #9103 planer. looking for a base plate. Any help would be greatly appreciated
 

Attachments

#42 ·
OK moving right along

Well, not really, but hey progress is progress even if its slow.

I never planned to take everything apart and repaint. So I dismantled the hood and a few misc parts, painted them up along with the new dust collection.

Plant Wood Rectangle Outdoor furniture Grass


Made a few rubber grommets to deaden the rattles.

Tints and shades Gas Wood Space Circle


The put it back together.
Added a 30' lengh of 10-3 power cord, connected to a new switch.

Wood Gas Machine Engineering Chair


Furniture Table Wood Gas Engineering


Took on last look at old unreliable.

Wood Table Hardwood Engineering Workbench


And set the new girl in her new home.

Attached the dust collection

Chair Tire Gas Flooring Mixing bowl


Furniture Table Wood Machine tool Gas


Wood Gas Machine Auto part Motor vehicle




I've now planed several rough sawn boards. The ability to take more than 1/16" is exceptionable. This one is so much quieter than the lunchbox too.

All that's left is the extensions and i want to make a small box that fits underneath to hold any related items such as extra blades, allen wrenches and such.

Thanks for looking.
 

Attachments

#43 ·
OK moving right along

Well, not really, but hey progress is progress even if its slow.

I never planned to take everything apart and repaint. So I dismantled the hood and a few misc parts, painted them up along with the new dust collection.

Plant Wood Rectangle Outdoor furniture Grass


Made a few rubber grommets to deaden the rattles.

Tints and shades Gas Wood Space Circle


The put it back together.
Added a 30' lengh of 10-3 power cord, connected to a new switch.

Wood Gas Machine Engineering Chair


Furniture Table Wood Gas Engineering


Took on last look at old unreliable.

Wood Table Hardwood Engineering Workbench


And set the new girl in her new home.

Attached the dust collection

Chair Tire Gas Flooring Mixing bowl


Furniture Table Wood Machine tool Gas


Wood Gas Machine Auto part Motor vehicle


Motor vehicle Table Wood Wheel Floor


I've now planed several rough sawn boards. The ability to take more than 1/16" is exceptionable. This one is so much quieter than the lunchbox too.

All that's left is the extensions and i want to make a small box that fits underneath to hold any related items such as extra blades, allen wrenches and such.

Thanks for looking.
Don that was quick :)
 

Attachments

#63 ·
Making the Knife setting jig

I know I could just go buy a knife setting jig, but some how spending $80+/- for something I'll use once or twice a year just didn't seem right. So I made my own.

First I found a piece of scrap cherry. I chose cherry because it was a piece of scrap the exact size I needed. I think its karma.

I then measured the width of the cutter head

Motor vehicle Automotive exterior Vehicle door Bumper Wood

-

I divided that in half and set my hole cutter to make the half circle.
-

Fluid Wood Floor Flooring Gas


A little sanding to get it just right.
-

Wood Flooring Floor Hardwood Wood stain


Verified the fit.
-

Wood Gas Tints and shades Bumper Hardwood


Drilled for the knife groove. (note its slightly off center)
-

Wood Natural material Wood stain Hardwood Apiary


Cut out a pattern for a better look and feel.
.

Wood Road surface Knee Tints and shades Asphalt


Drilled for the adjustment screw.
-

Wood Saw Gas Tool Machine


Found 2 more pieces of scrap and glued them for reinforcing the jig with the short grain direction.
-

Wood Amber Wood stain Hardwood Varnish


Tapped for the adjustment screw.
-

Wood Air gun Shotgun Natural material Gun barrel

-

Added the adjustment screw, nut and washer.
-
Wood Motor vehicle Gas Wood stain Hardwood

-
The using a good old fashion feeler gauge, set the adjustment screw to the current level of one of the knives. I checked the rest to find they were right on the money. I never moved them during the restore, so the last guy set them perfect.
-
Bumper Wood Tool Automotive exterior Saw

_

Set it off for the glue to dry.

The final steps were some light sanding and a coat of BLO, and resetting for blade height.
-
Bumper Motor vehicle Hood Automotive exterior Wood


Table Wood String instrument Plucked string instruments Fender


Light Table Wood Fender Gas
 

Attachments

#64 ·
Making the Knife setting jig

I know I could just go buy a knife setting jig, but some how spending $80+/- for something I'll use once or twice a year just didn't seem right. So I made my own.

First I found a piece of scrap cherry. I chose cherry because it was a piece of scrap the exact size I needed. I think its karma.

I then measured the width of the cutter head

Motor vehicle Automotive exterior Vehicle door Bumper Wood

-

I divided that in half and set my hole cutter to make the half circle.
-

Fluid Wood Floor Flooring Gas


A little sanding to get it just right.
-

Wood Flooring Floor Hardwood Wood stain


Verified the fit.
-

Wood Gas Tints and shades Bumper Hardwood


Drilled for the knife groove. (note its slightly off center)
-

Wood Natural material Wood stain Hardwood Apiary


Cut out a pattern for a better look and feel.
.

Wood Road surface Knee Tints and shades Asphalt


Drilled for the adjustment screw.
-

Wood Saw Gas Tool Machine


Found 2 more pieces of scrap and glued them for reinforcing the jig with the short grain direction.
-

Wood Amber Wood stain Hardwood Varnish


Tapped for the adjustment screw.
-

Wood Air gun Shotgun Natural material Gun barrel

-

Added the adjustment screw, nut and washer.
-
Wood Motor vehicle Gas Wood stain Hardwood

-
The using a good old fashion feeler gauge, set the adjustment screw to the current level of one of the knives. I checked the rest to find they were right on the money. I never moved them during the restore, so the last guy set them perfect.
-
Bumper Wood Tool Automotive exterior Saw

_

Set it off for the glue to dry.

The final steps were some light sanding and a coat of BLO, and resetting for blade height.
-
Bumper Motor vehicle Hood Automotive exterior Wood


Table Wood String instrument Plucked string instruments Fender


Light Table Wood Fender Gas
Very crafty on your part Don … let the chips fly!
 

Attachments

#72 ·
Making the Knife setting jig

I know I could just go buy a knife setting jig, but some how spending $80+/- for something I'll use once or twice a year just didn't seem right. So I made my own.

First I found a piece of scrap cherry. I chose cherry because it was a piece of scrap the exact size I needed. I think its karma.

I then measured the width of the cutter head

Motor vehicle Automotive exterior Vehicle door Bumper Wood

-

I divided that in half and set my hole cutter to make the half circle.
-

Fluid Wood Floor Flooring Gas


A little sanding to get it just right.
-

Wood Flooring Floor Hardwood Wood stain


Verified the fit.
-

Wood Gas Tints and shades Bumper Hardwood


Drilled for the knife groove. (note its slightly off center)
-

Wood Natural material Wood stain Hardwood Apiary


Cut out a pattern for a better look and feel.
.

Wood Road surface Knee Tints and shades Asphalt


Drilled for the adjustment screw.
-

Wood Saw Gas Tool Machine


Found 2 more pieces of scrap and glued them for reinforcing the jig with the short grain direction.
-

Wood Amber Wood stain Hardwood Varnish


Tapped for the adjustment screw.
-

Wood Air gun Shotgun Natural material Gun barrel

-

Added the adjustment screw, nut and washer.
-
Wood Motor vehicle Gas Wood stain Hardwood

-
The using a good old fashion feeler gauge, set the adjustment screw to the current level of one of the knives. I checked the rest to find they were right on the money. I never moved them during the restore, so the last guy set them perfect.
-
Bumper Wood Tool Automotive exterior Saw

_

Set it off for the glue to dry.

The final steps were some light sanding and a coat of BLO, and resetting for blade height.
-
Bumper Motor vehicle Hood Automotive exterior Wood


Table Wood String instrument Plucked string instruments Fender


Light Table Wood Fender Gas
Don slap a patten on it and name it. Sell it to Stumpy and make a fortune.
Good jig Don. That is American ingenuity at its best.
 

Attachments

#82 ·
The final Chapter Adding the extensions.

I had some extensions made and got them installed

Wood Floor Flooring Gas Machine


Gas Cylinder Flooring Human leg Machine


Wood Gas Machine Machine tool Hardwood


Then spent part of Monday turning this

Window Wood Flooring Fixture Floor


Into this…..

Wood Floor Flooring Plank Hardwood
 

Attachments

#83 ·
The final Chapter Adding the extensions.

I had some extensions made and got them installed

Wood Floor Flooring Gas Machine


Gas Cylinder Flooring Human leg Machine


Wood Gas Machine Machine tool Hardwood


Then spent part of Monday turning this

Window Wood Flooring Fixture Floor


Into this…..

Wood Floor Flooring Plank Hardwood
That is nice stuff, Don. Flooring, right?
 

Attachments

This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top