LumberJocks

brtech's Favorites

  • Advertise with us
View BritBoxmaker's profile

The EZ mitre technique

07-26-2010 10:55 PM by BritBoxmaker | 76 comments »

Hello all. Well I seem to have whet the appetite a bit so here goes for a ‘novel’ technique for making mitred boxes. Its a bit like making a box out of paper, like they showed you at school, using a ‘net’. Only in 3D, with wood and a tablesaw (not sissors). Well first comes the board Its made from alternating strips of Maple and Rosewood of varying thickness. I won’t bore you with the details on how to make it suffice to say that all the corners must b...

Read this entry »


View wnwoodworkingschool's profile

5 Cuts to a "Perfect" Cross Cut Sled

03-01-2012 02:39 AM by wnwoodworkingschool | 50 comments »

I’ve been getting a few email requests for a video on how I calculate the error ratio and how to correct and construct a cross cut sled that’s dead on square. I’ve been demonstrating this at the Woodworking shows for the past 5, 6 years and I still get emails asking me about the error ratio calculations. So here it is. Material List for sled:Runners: 5/16” x 3/4” x 30” Base: 1/2” x 34” x 30” Front Fence: 1-1/2” x 5” x 30R...

Read this entry »


View degoose's profile

How to make a endgrain tumbling block butcher block board!

08-12-2009 12:13 PM by degoose | 50 comments »

Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed. Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...

Read this entry »


View dewoodwork's profile

Beautiful end grain cutting boards free project plan

11-25-2007 07:31 AM by dewoodwork | 95 comments »

Construct these beautiful end grainCutting boards Hello fellow woodworkers,In the spirit of sharing woodworking knowledge I am writing this tutorial for anyone interested in constructing these beautiful end grain cutting boards. Take a look at the photos of the four styles I have made, or create your own pattern’s and follow the steps I have outlined in this tutorial. Questions and comments are welcome, enjoy. For this board I used maple, walnut, lyptus and purpleheart. White oak, wa...

Read this entry »


View SASmith               's profile (online now)

2nd Generation Chevron how to pictorial

11-20-2011 09:34 PM by SASmith | 9 comments »

I have had several LJs ask for a blog on this subject. Cut 30 degree strips to make a typical chevron Glue applied. The clamps have not been applied yet in the above picture.Draw 2 lines from like points to find the “D” point. Rough “A” points shown but will not be used in this pattern.Cut through “D” at 45 degreesThe 2nd generation emerging. My typical gluing set-up. Top and bottom cauls to keep the board flat. Plus cauls to apply even pressur...

Read this entry »


View rance's profile

Disposable KerfMaker

06-14-2011 08:35 AM by rance | 31 comments »

Well, yes, the Kerf Maker is a very clever jig. I have a different take on its manufacture. I see a reason to have several, NO, Wait… Why not make them DISPOSABLE? :) I had a need to use one today so why not make one. Here it is:  I used a stick of about 1/2” square pine. Yeah, Pine(or is that Poplar?). And some double sided tape. Cut the stick in half. (I’m kinda protective of my tape. Can ya tell?)  Then stick both halves together with the tape. &n...

Read this entry »


View Paul Pomerleau's profile

Bandsaw Series #3: Thien baffle using new circle jig on band saw

03-07-2011 05:03 PM by Paul Pomerleau | 8 comments »

I’m in the middle of constructing the famous Thien Separator and I needed to build a circle cutting jig to use on my band saw.I decided to make a video of it (my very first one) to share with you.You can view it here on YouTube.Hope you enjoy it.

Read this entry »


View SPalm's profile

Steps Cutting Board Version 2 (Two Step)

08-18-2010 03:03 AM by SPalm | 67 comments »

This is a second generation Steps cutting board made out of walnut, maple, and cherry. The first Steps board I made used a basic square with edge of maple and cherry to make it a block and a notch to do the stepping. I wanted to try to make a stepping board using the hex Tumbling Block design, and this is what I came up with. In order to make the hex do the stepping, I needed to notch all three sides, as can be seen in the Sketchup drawing. The cool thing here is that it steps in two di...

Read this entry »


View Lockwatcher's profile

Easy Shop Table

01-14-2011 04:02 AM by Lockwatcher | 37 comments »

I started this project after building an assembly table from an issue of Wood Magazine (March 2010). The table was a lot of work (the torsion box top) but the main unit holding the table up was an easy build. That’s when I hit upon the idea of using the same design for a group of extra tables for other uses. I’ve built a number of these already, and am using one as a router table, a miter saw station, and a sharpening station. It is built using standard re-dimensioned co...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase