This Week I show you how to make a folding out feed table for your table saw. This design was based after an article and plan found in a 2009 issue of Woodworker’s Journal Magazine. Originally the plan was designed for a Cabinet saw with a Biesemeyer Fence System, so I had to make some slight modifications for my Porter Cable Saw. In this 3 part video series I show you a step by step on building this project as well as talk about the modifications I had to make. The Article and plans ca...
The one Project Video I get asked the most to make is how to build a crosscut sled for the Tablesaw. Well there are a lot of videos out there on making a Cross cut sled, so this is my take on it. I hope you can take something from this video and use it in your shop
Recently I posted a video covering common woodworking joinery ( http://www.youtube.com/watch?v=zqXLYe783qw ) with the help of a few friends. In that video I talked to you all about making finger joints on the table saw and showed you a finger joint jig in the process. Well as I promised, here is the complete build process of that Jig. Table Saw Finger Joint Jig Also a little reminder about the 2nd Annual Whirligig Wars. It is almost here!! The event Runs from July 10 –...
I ask a couple of my woodworking friends to help me talk to you about some common woodworking joinery. Woodworking joinery is the method of joining two pieces of wood together to create a more complex item. Woodworking Joinery is the one thing we as woodworkers need to know and this video talks about 4 common woodworking joints that you are most likely to use in your projects. In this video you will learn about the following joints Half Lap Joints – Presented by Jay Bates Jays...
Hey everyone, Just wanted to share a couple of shop Jigs with you. One is a quick and simple jig for quartering your sheets of sandpaper to use in your palm sanders or sanding blocks. The second jig is a multi function tapering Jig that lets you do 4 sided tapers as well as straight edging rough sawn boards and cutting angles also.. There could be many more uses, there are just the 3 I focus on in the videos. Part 1 Part 2 Part 3
Recently I had a need to build a new table saw base for my saw. Rather than just building a simple replacement base, I opted to build one with lots of storage potential. This new base measures 6 feet long by 2 feet wide, which gave me good reason to move over to the new shop building. I haven’t yet finished the new shop set up ( haven’t even started) but this build is a great start giving me lots of options for storage potential… This build is a 2 part project. So be sure to...
Well, thanks to the comments and questions I have gotten I dug through my pics to find one I had on how to make a pot call. So for the folks that want a quick tutorial here we go. A pot call is basically a shallow dish containing two ledges inside. One is cut into the rim to hold the playing surface while the second is a ring left in the center raised to clear the bottom of the pot and still leave a space between the sound board that rests on it and the playing surface above it. One thi...
:O) I am a bit excited. I finally have a set of GRR-Rippers in the shop. I have been wanting one for a long time. So I put together this video to show you just a couple reasons why I am pumped up about these helpful shop accessories. Not only are they keeping me safe, but they are allowing me the opportunity to perform tasks I couldn’t perform before… That in itself has got me doing backflips… lol Here is a look at the video
This is part 1 in a series I am doing on pen making for beginners. A friend of mine asked me to teach him and said he wished it was on video so he could watch parts back. So here we go. Thanks for checking it out. Video
One of my favorite pass times is playing pool (Billiards) and I thought this would be a cool project to share with you. If you have a pool table in your house or man cave or if you know someone who owns a pool table this would be a great gift to give… Also be sure to check out and subscribe to my new Youtube Channel “The Rundown” to get follow ups on my main project videos, that are on my main channel, as well as the rundown on small easy to build projects, ...
- My Journey As A Scroll Saw Pattern Designer - 1509 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 94 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- Sheila Landry (scrollgirl) - 1533 entries
- frank - 417 entries
- degoose - 394 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- William - 258 entries
- mafe - 252 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- shipwright - 207 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 187 entries
- Rustic - 186 entries
- Chris Davis - 183 entries
- BritBoxmaker - 177 entries
- Smitty_Cabinetshop - 165 entries