LumberJocks

Woodworking blog entries tagged with 'work bench'

  • Advertise with us
View PanamaJack's profile

Workbench 101

02-05-2008 09:22 PM by PanamaJack | 25 comments »

Over the past several years I have been needing and wanting to buy or maybe just make a workbench. I have gone to five woodworking shows in three states over the past two years. At these shows and in several magazines or catalogs I have noticed many of these really nice woodworking benches that are way far out of my reach as far as the $$$ involved. Finally after a elongated sick spell lasting nearly two months I finally get few boards together, screws, a very few nails and other items tha...

Read this entry »


View CartersWhittling's profile

Workbench #13: Tail Vise Is Complete

10-19-2011 01:31 AM by CartersWhittling | 20 comments »

Hello. I have now finished the tail vise, and today I had acually started work on the base. After I had got the dovetails for the tailvise fit and the pins on the guide rod I cut out the place for the pins to be inserted in the vise assembly. I then started work on getting the notches cut in the guide blocks for the sliding parts. Here you can see the guide rod in place, with the one guide block attached to the end cap with a notch for the guide rod to slide through aswell as a small notch...

Read this entry »


View Jeremiah's profile

Leg Vise, Shop made #2: Time to start over from scratch

10-22-2013 03:10 PM by Jeremiah | 8 comments »

Here is the leg vise i made, it works OK, but i can tell the force it puts on the mounts i made are going to fail over time. (see pic below) Then i came across this picture of an old black smith vise and wondered why hadn’t anyone one done one like this before? seemed simple, strong and fairly fool proof (ie Me Proof) So off i went to build my own:1st i turned a wheel using 2 pieces of 6/4 hard maple, laminated together.then i epoxied and pinned some 3/4” acme rod...

Read this entry »


View jmos's profile

Work Bench Build #7: Finished!

03-20-2012 06:07 PM by jmos | 17 comments »

Well, I haven’t gotten a lot of time in the shop lately, but I did get two coats of BLO on the bench, and I’m calling it complete. Overall I’m happy with the way it turned out. I might still ad a shelf underneath, or I’ll just store my bench jigs on the floor underneath. I installed a wall mounted shelf and tool rack, so most of what I need easy access to is just behind the bench in easy reach. I’m happy with how the LVL worked out...

Read this entry »


View jusfine's profile

Roubo Inspired Bench #5: Getting closer - finally getting the slabs on top of the bench, & an orange dog or 2

05-25-2013 09:51 PM by jusfine | 8 comments »

The rails have been assembled, legs attached to the cabinet, a little clean up and should be ready to mortise for the slabs. It appears I have some corrupted images on my memory card, so may not be able to post any of the photos of mortising or attaching the slabs through the rails with the SPAX type screws. Slabs have been fastened to the top with one screw at each end, there is a 2” gap between the two sections. I wanted a wide enough space to be able to use a Be...

Read this entry »


View grfrazee's profile

SYP Spilt-Top Roubo Workbench #3: (Mostly) Finished Tail Vise

01-28-2013 05:00 PM by grfrazee | 3 comments »

Previously, I had run out of time to complete the tail vise on my workbench: This weekend I finally got the time to remedy that situation. I started off by routing the dog holes in one of the boards, then gluing up the leg vise block. The dog holes are spaced at 3” for versatility. Then I needed to figure out what to remove for the various pieces of the vise hardware. Some time was spent with the adjustable square to figure out the recess locations. Note: the measureme...

Read this entry »


View bfd's profile

A Solid Foundation to Build a Future - A New Workbench #2: The base comes together

04-24-2009 08:55 PM by bfd | 18 comments »

So my 3 sheets of veneer arrive and I open them to inspect them. I opted to use 2 ply 4×8 sheets to save time vs. laying up my own veneer. Out of the 3 sheets I rejected two, one walnut sheet which was supposed to be flat cut and the maple sheet which I paid a premium for to have wider leaves. The walnut piece didn’t have any cathedraling in it at all and was made up entirely of the quartered portion of a flat cut piece of veneer. The supplier worked with me to get me repla...

Read this entry »


View CartersWhittling's profile

Workbench #18: Thoughts and Changes

05-16-2012 02:25 AM by CartersWhittling | 15 comments »

Hello. Its been 6 months since I finished my bench and I have spent over 1000 hours on it. Now that I have gotten a good feel for how the bench works and its ups and downs I thought I would write an update on it. To start I’ll mention the modifications I made. The first was to add leather to the pads on the hold fasts. With leather I no longer need to place scrap wood between the work pieces and the hold fasts to prevent denting. If you have hold fasts (which you should) I would r...

Read this entry »


View bfd's profile

A Solid Foundation to Build a Future - A New Workbench #3: The Top

08-24-2009 01:25 AM by bfd | 13 comments »

This has been an off and on project for me for several months. I have put it on the back burner to take a few commisions and finally got around to working on the top. To make things easier on me from a time stand point I bought a premade butcher block top and added the aprons saving me the time of milling all that lumber. The first thing that I tackle is routing the tongue on each end that will support each end cap. I route a 3/4” groove on each end cap. Next I layout the dove...

Read this entry »


View mafe's profile

Workbench restore (Scandinavian style) #5: Making bench dogs.

11-11-2012 02:52 PM by mafe | 13 comments »

Scandinavian workbench restoreMaking bench dogs. Time for bench dogs, the show must go on… First was to cut three pieces of wood into the right size.The bench dog holes total size and the length I choose to be app double the thickness of the bench top. On the left you see the only dog that came with the bench… I guess this dog cant bark a lot…So time to make some marking, now the shape comes and I simply follow the measures of the dog holes in the bench top. This time I use ...

Read this entry »


1 2 3 4 ... 6 next »
58 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase