During the recent posting by Bertha on the hand planes of our dreams, the issue of wooden shoulder planes came up. I had some requests and PM’s to blog on the making of a wooden shoulder plane so I will give it my best shot. Be warned, I work in the metric system so measurements are in millimeters. For those who use King George’s thumb to measure, dividing by 25.4 will at least give decimal inches. I’ll gladly answer any question but have patience: No computer will survive in my dusty worksho...
24 hours later and I’m back in my favorite chair! It sounds like some has already sourced plane irons in many different ways. Good! Bertha is ordering a brandnew blade, Derosa found some old plane blades at a local junk store and his Dremel with cutting disc is eager to go! Grittyroots has some old molding planes and wants to use an iron from on of those. Bearpie in Jacksonville has some old worn out metal cutting saw blades about 1/8” thick by 2” wide and 18” long. Good ide...
Building a wooden shoulder plane #3: The mouth. Don't open wide, we are not at the dentist! (sorry Ken)
As I write, my blue Monday is behind me but some of my American friends are still busy dealing with theirs! Let’s get rid of the blues and go back to our project. The glue is dry and we can pop the clamps. I’ve always liked this stage of a project, that moment when you can take off the clamps and clean up the glue lines. Again, a reminder of what we want to achieve: This is where we are. Cut the pins close to the timber and clean up the glue lines. If there is glue squeeze ou...
So here we go again. It looks like you folks are having fun making some wooden planes so lets add to the fun. Here is a great little coffin shaped smoother for your collection. This is a fantastic size and a great introduction to making a wooden bench plane. The construction of the parts is a very typical arrangement and the size of wood needed to make this is much easier to find. Here are the plans in several different layouts. The download has four pages. First one is for shop reference ...
I thought “What if I coated the whole ring in cyanoacrylate finish?” ...and I tried it. The rings have since been through regular everyday wear including dishwashings, handwashings and showers. END RESULT: This finish is holding up better than both Waterlox and Arm-R-Seal. And, in my opinion, it actually looks better. CAVEATS: Obviously, this would be difficult to do on anything but very small woodworking projects. It’s just right for these wooden rings, but ...
Body done, wedge done, plane iron done. If you are anything like me, eagerness to see some shavings has replaced all other desires at this stage! With a bit of luck, paper thin shavings will be curling out of the mouth. Isn’t it great! If not, don’t despair…. LET’S FINE TUNE: 1. True the plane sole. This is done with the blade in place but well away from the mouth and the wedge set up tightly as it would be in use. Why? With the wedge set, our plane is in “tension”. The wood actuall...
So in the spirit of getting everyone in the shop and cutting up some wood I decided to post up a measured drawing of a 3/4” wooden rabbet plane in the 18th century style. It is all wood with the exception of the blade which is easily gotten from Lie-Nielsen here. It features a conical escapement and some simple embellishments that a hand plane, chisel, and #7 sweep gouge can handle. The plans are basic with a few things that can be easily changed if you like. Such as the bed angle...
After posting the pictures of The Rising I was asked by a couple LJ’s to post more information on the mechanism I designed to lift the book. Since I do not have the box anymore I took some screen shots from the 3D modeling software I use for initial designs (SolidWorks if anybody is interested. It is the program I use at work). Below I show the mechanism in its lowered position. Here it is half way through its motion. And here it is at the top of its motion. I think t...
Why buy it when you can build it? That’s my motto. Every woodworker is going to need clamps. I knew I would need some for my bench… especially when gluing up the top. Speed clamps and pipe clamps are great if you can afford them, but everywhere I read I see you can’t have too many clamps… Well until Angelina Jolie decides to adopt me too, I’m going to have to do it another way. I found an article in an old Popular Mechanics magazine showing how to build ...
It makes me REAL happy to see that some guys have been inspired to make their own planes! For that reason, I will patiently bear the slowness of my backwater farm style dial up connection….. The last part to be made is the wedge. Just a simple piece of wood but with a very important function! Not only does it hold the blade firmly in position, it also acts as a chip breaker of sorts. Remember when we made the plane body (Part II) there was this little off cut piece to be saved? This...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 106 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 419 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 214 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 194 entries
- A Slice of Wood Workshop - 190 entries