This Week I show you how to make a folding out feed table for your table saw. This design was based after an article and plan found in a 2009 issue of Woodworker’s Journal Magazine. Originally the plan was designed for a Cabinet saw with a Biesemeyer Fence System, so I had to make some slight modifications for my Porter Cable Saw. In this 3 part video series I show you a step by step on building this project as well as talk about the modifications I had to make. The Article and plans ca...
The one Project Video I get asked the most to make is how to build a crosscut sled for the Tablesaw. Well there are a lot of videos out there on making a Cross cut sled, so this is my take on it. I hope you can take something from this video and use it in your shop
Recently I posted a video covering common woodworking joinery ( http://www.youtube.com/watch?v=zqXLYe783qw ) with the help of a few friends. In that video I talked to you all about making finger joints on the table saw and showed you a finger joint jig in the process. Well as I promised, here is the complete build process of that Jig. Table Saw Finger Joint Jig Also a little reminder about the 2nd Annual Whirligig Wars. It is almost here!! The event Runs from July 10 –...
Recently I had a need to build a new table saw base for my saw. Rather than just building a simple replacement base, I opted to build one with lots of storage potential. This new base measures 6 feet long by 2 feet wide, which gave me good reason to move over to the new shop building. I haven’t yet finished the new shop set up ( haven’t even started) but this build is a great start giving me lots of options for storage potential… This build is a 2 part project. So be sure to...
I ask a couple of my woodworking friends to help me talk to you about some common woodworking joinery. Woodworking joinery is the method of joining two pieces of wood together to create a more complex item. Woodworking Joinery is the one thing we as woodworkers need to know and this video talks about 4 common woodworking joints that you are most likely to use in your projects. In this video you will learn about the following joints Half Lap Joints – Presented by Jay Bates Jays...
Hey everyone, Just wanted to share a couple of shop Jigs with you. One is a quick and simple jig for quartering your sheets of sandpaper to use in your palm sanders or sanding blocks. The second jig is a multi function tapering Jig that lets you do 4 sided tapers as well as straight edging rough sawn boards and cutting angles also.. There could be many more uses, there are just the 3 I focus on in the videos. Part 1 Part 2 Part 3
:O) I am a bit excited. I finally have a set of GRR-Rippers in the shop. I have been wanting one for a long time. So I put together this video to show you just a couple reasons why I am pumped up about these helpful shop accessories. Not only are they keeping me safe, but they are allowing me the opportunity to perform tasks I couldn’t perform before… That in itself has got me doing backflips… lol Here is a look at the video
One of my favorite pass times is playing pool (Billiards) and I thought this would be a cool project to share with you. If you have a pool table in your house or man cave or if you know someone who owns a pool table this would be a great gift to give… Also be sure to check out and subscribe to my new Youtube Channel “The Rundown” to get follow ups on my main project videos, that are on my main channel, as well as the rundown on small easy to build projects, ...
Well I finally finished the Tablesaw Base, trying to film during rain storms is almost impossible with the ambient noise from the rain hitting the metal roof.. but I waited it out, and am very happy with the outcome.. Here is a look at the final steps of building this base
This week I decided to rebuild my tablesaws extension wing/router table. This time I removed the factory metal wing along with my old router table extension and built a new wing using the MDF and famica from last weeks build. This new extension wing combos as a router table as well as it has a pull out support arm that allows me to support my material as i cross cut long boards or sheets goods no matter if I am using a sled or not, because the support arm is adjustable. Here is a look at some...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 105 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 418 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 245 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- A Slice of Wood Workshop - 190 entries