Sharpening chisels—forget weaker micro bevels Controversial though it may seem, and though adopting micro-bevel methods for sharpening chisels may seem to make sense, a freehand convex bevel actually gives exactly the same sharpness as any micro-bevel method, but takes only a fraction of the time to develop. A convex bevel keeps its edge longer, is stronger than most other bevels and needs no special equipment beyond a pair of hands. Establishing the skill to sharpen the convex camber ...
Clark Little's Photography is probably one of my greatest sources of inspiration. I am a huge beach bum and love to surf, but my passion for the ocean goes further then just enjoying it, I am inspired by it. Here are just a few of Clark Little’s Photos that inspire me the most.
This bridge fell during a tropical storm a few years ago. Now it servers as a dam, and the river flows over it rather than under. Today cars do not use the bridge to travel the forest road, but that doesn’t stop a few adventurous hikers. The bridge. Wire frame showing the construction of the table The woods depicted in the table design are primarily cherry and maple, with walnut accents.Front View Left View The table. Joint Detail This is my first project in sketc...
Fish Out of Water – Intarsia Woodworking Most everything that I do, I do with someone in mind and/or for some reason. I very rarely make something just to make it. I found a picture a while back that I really liked of a fish jumping up out of the water to catch a dragon fly. What drew me to this design was the way the water seemed to splash right out of the frame over a log. I had it printed and held on to it until now. My brother-in-law had a band saw that he never used and it see...
So the first piece was really a “how does the trigger works” more than anything. some positions felt a bit awkward, and others’ were a mystery but all in all, a good learning experience. as I posted earlier, the 1st piece is in front, while the original piece is in the back: Lesson Learnt: With the second piece, I followed some given advice added to the already advice I’ve been collecting online for the past who knows how long from people like Charles Neil...
I have been doing a little research into a bowl finish that will handle boiling water. I e-mailed General Finish and here’s the exchange: Me: Is General Finishes Salad Bowl Finish, when cured, safe to use for applications that come in contact with boiling water? GF: ... a better product would be our new water base wood turners finish, it is water base and has no odor- so you would not have to wait a month to use it. I would still wait a good two weeks for the product to cure befo...
I was able to plane the stock for the shelves yesterday. I glued up a large enough blank for two shelves, then used the fence to cut them parallel. I then used the cross-cut sled to square the other sides. I got to use my Delta new mortiser to make all of the mortises (3 on each side x 4 sides = 12 total). Luckily, they were all 3/8” and had the same offset from the front/back. This meant that with one setup, I could knock them all out. If I had done them with a chisel, ...
So, in response to my previous post – I’m only working on the right side of the closet design and I only have 6 shelves at the moment instead of 7. The wood I ended up getting was “Whitewood” which seems to be some kind of spruce or pine. It’s pretty light and soft. I got it because it was pretty cheap and the width was perfect so I didn’t have to do any ripping. I did end up getting a circular saw but there was a massive snow storm so I had to work indo...
Don’t be afraid of wood & water. Wood loves the stuff. Most of the tree is water when it’s standing. It’s why they’re so heavy when they come down. It’s all that water inside of them. Once I had a 1/2” thick maple table top, 20” square, all shaped and sanded. I decided to raise the grain and sand it off. Wet sanding I call it, although I wait for the water to dry and just sand off the fuzz raised up by it. Well I wet down this top and it cupped...
When cleaning furniture, a little water is usually all you need. Most of the time you don’t need store bought furniture polishes or waxes. Most furniture these days just need to be dusted and if really dirty cleaned with a moist rag. Wax will build up and can leave the finish streaky and sticky. Some products may even have a solvent in them to cut oil and grease that can soften the finish of the piece. What I normally do is wet a rag and wring it out as much as possible. This le...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 105 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 418 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 245 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- A Slice of Wood Workshop - 190 entries