Woodworking blog entries tagged with 'video'

  • Advertise with us
View CharlieK's profile

Behind the scenes of my shop and YouTube channel #8: Special visit by LJ's own Doc Savage!

10-15-2016 01:35 AM by CharlieK | 8 comments »

View on YouTube Last week I was lucky enough to have LJ’s own Doc Savage visit my shop. Of course I put him to work while he was there!! All kidding aside, it was nice of him to stop by and we had a really nice visit. Anyway, I shot some video of him while he was here and included it in my most recent shop update. Among that and other things, I also discuss having a little trouble with a minor upgrade to my Festool Domino. Check it out and...

Read this entry »

View A Slice of Wood Workshop's profile

Make a Sander Organizer

10-14-2016 09:13 PM by A Slice of Wood Workshop | 0 comments »

I had to organize all my sanders and sandpaper. I used 1×8 and some 1/4” plywood. Check it out, subscribe and share the video. Visit my channel here.

Read this entry »

View ShogunJimi's profile

Bench Restore

10-13-2016 03:17 AM by ShogunJimi | 0 comments »

This build was a result of a challenge from another you-tuber named Opa Koster. I really liked the results and wanted to share the pictures and video here on lumberjocks. The bench was bought from a local antique store and was painted with some ugly green paint over the wood and cast iron. I had quite a task to remove that paint and primer from the cast iron. I liked the back cast iron piece but I envisioned a different project for it. So it has been saved it for a later project ...

Read this entry »

View WmWalkerCo's profile

The progression of my workshop #4: How to Set Up a Jointer

10-11-2016 11:23 PM by WmWalkerCo | 0 comments »

I recently acquired a Bridgewood BW8J 8” Jointer and made a video on setup and tuning it up. You can watch the video here: How to Setup a Jointer

Read this entry »

View A Slice of Wood Workshop's profile

Turning an Acrylic Bottle Opener

10-11-2016 06:33 PM by A Slice of Wood Workshop | 0 comments »

Had a fun trip to wood store. Did some welding and was able to turn a bottle opener. Check out the Vlog and subscribe for weekly videos.

Read this entry »

View dbhost's profile

Dave Talks #11: Prepping the mount board for the structured wiring. Part 3. Drywall.

10-11-2016 05:16 PM by dbhost | 3 comments » In today’s video I show you how to care for you measure and cut a wall penetration for a 3 gang low voltage pass-through for all of these structured wiring including the ethernet cables telephone and TV coaxial cables. We end up with a good tight fit dead center where we want it and completely level it couldn’t have gone better.

Read this entry »

View BenhamDesign's profile

Building a Beetle Kill pine table with a chandelier base

10-11-2016 04:52 PM by BenhamDesign | 1 comment »

This post is an overview of the build. If you want more info please visit my personal blog post. Building a Table by Re-Purposing a Chandelier Watch it be built on YouTube I started out with the chandelier my wife hated. I used a cut off wheel to remove anything that wasn’t going to be part of the base. I aligned the legs using a scrap piece of plywood clamped in the vise Used Tie wire to hide the holes where the electrical wire came through. Painted wire a fra...

Read this entry »

View Mosquito's profile

Making a Shadowbox #7: Door Frame and French Cleat

10-10-2016 04:36 PM by Mosquito | 3 comments »  This time around, I finish up the pieces for the door, and make the french cleat for hanging the box.  Case Mod Portfolio: http://themodsquito.comFacebook:

Read this entry »

View DrDrewInOhio's profile

Woodworkers in NE Ohio #8: - We are over 340 members now !

10-09-2016 04:50 PM by DrDrewInOhio | 1 comment »

If you are in or near NE Ohio, come out of the virtual world and join us! We are a Woodworking MeetUp Group that is dedicated to promoting the Art of woodworking. Search for Woodworking Groups on… and see what we do.

Read this entry »

View Slavisa Nesic's profile

Sketchup extension - FitParts for cut plans

10-09-2016 10:40 AM by Slavisa Nesic | 0 comments »

I’ve made a Sketchup extension named FitParts for generating cut plans from your drawing. Let’s say you are making a panel box just for example. First you make 6 walls and group every one of them as you go; it is nice and normal to name them, say left, right, .... Second you select these groups. Third you start my extension from Sketchup menu Extensions / FitParts / MakeCutlist. You will choose or type the size of (identical) panels you have and click the Cut button.What you will...

Read this entry »

« prev 1 2 3 4 5 ... 492 next »
4920 entries

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics