LumberJocks

Woodworking blog entries tagged with 'veneering'

  • Advertise with us
View kiefer's profile

MAKING OF A COFFEE TABLE (PART5)

01-28-2013 03:32 AM by kiefer | 9 comments »

Well it has been a anxious and emotional week for me and not much got done on the table but such is life.This week I played around of and on with some yellow glue and some 1/8” walnut veneer ,I rolled on glue on both surfaces (three different types seen in the pic ) and let the samples dry until clear and layed it on the plywood , put a hot iron on the veneer and heated the glue until it bonded and followed with a piece of wood to rub it flat .The result was a nice strong bond and tryin...

Read this entry »


View CJay's profile

Shop-made veneer/nipping press #3: Finishing off

01-20-2013 12:43 PM by CJay | 1 comment »

Mdf plates to protect the faces of the press, they should also make getting stuff into the press easier. Plugged cleaned up (a bit) and oiled. All finished and ready for use.

Read this entry »


View CJay's profile

Shop-made veneer/nipping press #2: Assembly

01-16-2013 08:23 PM by CJay | 2 comments »

Time for the joinery Tennons done on the table saw Mortices done with a drill and a chisel (yes i am working in the kitchen. It’s winter here and my workshop has no heating) Parts ready for assembly, Top and bottom all ready part assembled. Test run. All glued up. In this case epoxy, strength is needed. Holes have been drilled to take screws so no need for clamps. These’ll be pluged when it dried.The up and down bit is too tight and will ne...

Read this entry »


View Bob Simmons's profile

Bandsaw Resaw Method

01-15-2013 07:05 PM by Bob Simmons | 17 comments »

This is a bandsaw resaw method that I much prefer over the traditional method of resawing. In the following article I share the advantages of this resawing method. How to Cut Great Veneer The Apprentice and The Journeyman ...Learn more, experience more!

Read this entry »


View kiefer's profile

THE MAKING OF A COFFE TABLE (PART ONE )

01-15-2013 05:26 AM by kiefer | 10 comments »

This is a blog of a build of a coffee table that I have been mulling over for about a year and finally started building it as my wife likes the idea so far, I build a some what crude model to give her a better picture then I could draw.!OK this is the basic concept but the final design will be done in the shop and be different then what you see .To start I build a form for the two base arches and I did not take pics of the build but it is simply five identical curved 1/2” plywood ribs o...

Read this entry »


View CJay's profile

Shop-made veneer/nipping press #1: basic parts

01-13-2013 09:34 PM by CJay | 3 comments »

As i’ve lost all access to the veneer press at college and not being able to afford a vacuum press i’ve been looking at book-binders (or nipping) presses. ...which are still several hundred pounds. Plan B:- make one. I have no real plan for this, just a general idea. Here we go. The top, bottom and press are made out of any sheet material i could find.Cut it up, stick it back together to make thicker boards and trim to size (400mm x 300mm) At this point i act...

Read this entry »


View Bob Simmons's profile

Shop Made Wood Inlay Banding - 45 Degree Diamonds

01-03-2013 09:28 PM by Bob Simmons | 9 comments »

Shop Made Wood Inlay Banding – 45 Degrees Diamonds. Watch how to assemble and glue the maple and walnut segments together to form a decorative wood inlay banding. The diamond pattern is of 45 degrees. All the wood segments have been accurately and uniformly cut on the band saw with the aid of a few specialized band saw sleds. In this woodworking video you’ll see the woodworking methods that the woodworker uses to produce a nice, tight pattern for the banding “log̶...

Read this entry »


View Bob Simmons's profile

Cosmatesque #4: Picture Frame - Cosmati Wood Inlay

12-27-2012 05:50 PM by Bob Simmons | 8 comments »

Picture frame of Cosmati wood inlay design. Learn woodworking methods and techniques for picture frame making. Learn how to inlay a wood inlay banding with wonderful designs of sacred geometry based on a cosmatesque pattern. Watch the methods and techniques employed by the woodworker to create the wood inlay banding in the workshop. Band saw sleds are used to create uniform segments for the inlay banding. White glue is used for its slow setting capabilities and the fact that it dries cl...

Read this entry »


View Bob Simmons's profile

Cosmatesque #3: Cosmati Wood Inlay Banding - Part 3

12-21-2012 04:35 PM by Bob Simmons | 8 comments »

Watch how the Cosmati design is applied to wood inlay banding in Part 3 of this woodworking series. All the wooden segments have been cut on the band saw using cross cut sleds made in the workshop. The segments have been glued up to form the inlay banding “log’ and the woodworker is now prepared to joint an edge of the log so that thin strips of 3/32” veneer can be sliced on the band saw. A Rockler thin rip jig is placed and secured into the band saw miter gauge a dist...

Read this entry »


View OregonBurls's profile

Only for LumberJocks... Free shipping at Oregonburls

12-14-2012 08:53 PM by OregonBurls | 1 comment »

Hey everyone. I am offering exclusively to LJs frees shipping at www.oregonburls.com Here is the scoop!Orders over $75 I will pay for shipping excluding slab or heavy items (only in the USA). Email me with what you would like and I will invoice you and give you free shipping.Dont forget to sign up for the monthly wood give away.greg@oregonburls.comPlease spread the word Merry Christmas!

Read this entry »


« prev 1 ... 4 5 6 7 8 9 10 ... 29 next »
286 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com