LumberJocks

Woodworking blog entries tagged with 'veneering'

  • Advertise with us
View Bob Simmons's profile

Diamond Inlay Banding #1: Make a Picture Frame - Part 1

553 days ago by Bob Simmons | 8 comments »

Watch and learn how to make a picture frame with diamond inlay banding. In Part 1 of this woodworking series the woodworker demonstrates of to use a mallet and a chisel to create the mortises of the decorative wooden pyramids. This hand tool work takes place at each miter joint of the picture frame. Once the mortises are made, the woodworker will then have a reference points of where the diamond wood inlay banding will begin and finish. The wooden pyramids are not glued in at this time....

Read this entry »


View kiefer's profile

MAKING OF A COFFEE TABLE (PART 6)

556 days ago by kiefer | 11 comments »

Well it has been some time that I worked on this table but there are things that have priority when you work for a living .I have installed the outside veneer on both halves of the base and started today with the inside veneer . The iron seemed the biggest obstacle and as I mentioned previously using a heat gun as a alternative got nixed because of the expense involved .I designed a round sheet metal base for the iron using some thin sheet metal with steel wool inside to give it a flex...

Read this entry »


View Bob Simmons's profile

Router Inlay Practice - The Diamond

560 days ago by Bob Simmons | 13 comments »

This is a routing technique that can be used with great accuracy when inlaying wood veneer. A compact router is used along with a shop-made router template. The video was taken during a time of router inlay practice within the woodworking shop. Sometimes it’s nice to be able to relax, experiment in the shop to develop methods of work for an upcoming woodworking project. Your comments are welcomed. Routing Wood the Easy Way ...The Apprentice and The Journeyman ...Learn more,...

Read this entry »


View Bob Simmons's profile

The Joy of Making Wood Inlay Banding

562 days ago by Bob Simmons | 13 comments »

Once the “banding log” is completed it’s a great feeling to slice veneers of wood inlay banding on the band saw. This banding log will produce quite a few veneers that will be inlaid into a number of upcoming woodworking projects. Answers to common questions….The wood inlay banding is sliced to 3/32”. A 1/2” WoodSlicer resaw band saw blade is used when ripping the veneer. The blue jig is a Rockler thin rip jig. (It has a roller bearing.) The wood i...

Read this entry »


View Bob Simmons's profile

Router Inlay Practice - The Compass Rose

570 days ago by Bob Simmons | 12 comments »

Router Inlay Practice Question: How would you inlay a 2 inch wide compass rose veneer? It has a thickness of 3/32”. The techniques demonstrated by the woodworker in this woodworking video are basically just for practice. He is simply testing to develop a strategy for when it becomes time to actually inlay the compass rose veneer. Practicing woodworking in the shop is a great idea. It’s a good way to develop confidence in one’s skills and to develop new techniques. Plus, we all...

Read this entry »


View kiefer's profile

MAKING OF A COFFEE TABLE (PART5)

570 days ago by kiefer | 9 comments »

Well it has been a anxious and emotional week for me and not much got done on the table but such is life.This week I played around of and on with some yellow glue and some 1/8” walnut veneer ,I rolled on glue on both surfaces (three different types seen in the pic ) and let the samples dry until clear and layed it on the plywood , put a hot iron on the veneer and heated the glue until it bonded and followed with a piece of wood to rub it flat .The result was a nice strong bond and tryin...

Read this entry »


View CJay's profile

Shop-made veneer/nipping press #3: Finishing off

578 days ago by CJay | 1 comment »

Mdf plates to protect the faces of the press, they should also make getting stuff into the press easier. Plugged cleaned up (a bit) and oiled. All finished and ready for use.

Read this entry »


View CJay's profile

Shop-made veneer/nipping press #2: Assembly

582 days ago by CJay | 2 comments »

Time for the joinery Tennons done on the table saw Mortices done with a drill and a chisel (yes i am working in the kitchen. It’s winter here and my workshop has no heating) Parts ready for assembly, Top and bottom all ready part assembled. Test run. All glued up. In this case epoxy, strength is needed. Holes have been drilled to take screws so no need for clamps. These’ll be pluged when it dried.The up and down bit is too tight and will ne...

Read this entry »


View Bob Simmons's profile

Bandsaw Resaw Method

583 days ago by Bob Simmons | 17 comments »

This is a bandsaw resaw method that I much prefer over the traditional method of resawing. In the following article I share the advantages of this resawing method. How to Cut Great Veneer The Apprentice and The Journeyman ...Learn more, experience more!

Read this entry »


View kiefer's profile

THE MAKING OF A COFFE TABLE (PART ONE )

583 days ago by kiefer | 10 comments »

This is a blog of a build of a coffee table that I have been mulling over for about a year and finally started building it as my wife likes the idea so far, I build a some what crude model to give her a better picture then I could draw.!OK this is the basic concept but the final design will be done in the shop and be different then what you see .To start I build a form for the two base arches and I did not take pics of the build but it is simply five identical curved 1/2” plywood ribs o...

Read this entry »


« prev 1 2 3 4 5 6 7 ... 27 next »
261 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase