LumberJocks

Woodworking blog entries tagged with 'veneering'

  • Advertise with us
View CJay's profile

Shop-made veneer/nipping press #3: Finishing off

01-20-2013 12:43 PM by CJay | 1 comment »

Mdf plates to protect the faces of the press, they should also make getting stuff into the press easier. Plugged cleaned up (a bit) and oiled. All finished and ready for use.

Read this entry »


View drewnahant's profile

a small writing desk start to finish #1: design and drawing

03-17-2011 03:47 AM by drewnahant | 1 comment »

I have been thinking about making something in a more classical style for a while. The decision of what to make was actually an afterthought, im building it mostly for fun and practice, so I was more concerned with style, technique, and joinery, but here’s the criteria I came up with -Incorporate turning ( I enjoy turning, but have never actually turned a set of spindles, legs, or any other kind of matching set)-Mortise and tennon joinery ( I’m in the middle of building a p...

Read this entry »


View Huckleberry's profile

Desk Build #2: Layouts, cuts, and more.

08-16-2010 05:57 AM by Huckleberry | 1 comment »

So here is part two of this series on making these desks. I show you how I layout my sheet goods and yes I did solve my quandary of the pencil drawer grain. So I hope that this is entertaining and educational for all.

Read this entry »


View RichClark's profile

YAPPING inloud #1: Boxes for girls

04-27-2011 01:53 AM by RichClark | 1 comment »

Making some pretty boxes for my Nieces and Daughter. This one in under construction and redesign allot. The only part I like is the top I made.I wanted to try Parquetry and bought some selections of wood veneers and give it a shot. So this is where I am Mahogany sides, Ebony Frame and My picture of the favorite flowershe likes… Its almost done and it looks like this so far… So I will post a project for it when its done…

Read this entry »


View WordCooper's profile

Koa, anyone?

11-12-2011 07:18 PM by WordCooper | 1 comment »

Anybody in the Portland-Vancouver area looking for some rare Koa wood from Hawaii? I have a beautiful slab from Maui, about 57” long by 15” wide by just over 2” thick—almost 12 board feet of this rare and gorgeous wood. This is a section cut through the base of a branch so it includes some wonderful crotch grain. One significant check, which still allows two major cuttings—one of about 52”x5”x2,” and one of about 48”x7”x2...

Read this entry »


View Shawn Sealer's profile

Ep. 22 MCCC AKG Box Part 3

04-15-2012 06:14 PM by Shawn Sealer | 1 comment »

In this episode:Gluing up the box. Cutting the splines. Separating the lid.

Read this entry »


View Tom8021's profile

foot powered Scroll saw #2: foot powered Scroll saw #2:

07-16-2009 09:01 PM by Tom8021 | 1 comment »

Let’s go over what my dimensions are: I used scraps I had around the shop, Base 32×16 x 3/4 melaminetable 36×12 x 3/4 melamine Arms 36×3/4×5/8 oakarm support (rides on top of the arm) 30×5/8×1 1/2tower 2 1/2×7/8×13 from the base You can see the arm top and arm are glued together perpendicular to each other for strength. The arms are attached about 4” in from end with the lower arm 3” off the base and the upper 8”...

Read this entry »


View Tom8021's profile

foot powered Scroll saw #4: The Tower

07-17-2009 07:33 PM by Tom8021 | 1 comment »

The tower needs to be beefy. I had some 7/8 ASH laying around so I used it. Everything hinges on the tower so don’t be shy adding a few bolts. The lower part ( 2 1/2×15 1/2) is just bolted to the base with three lag bolts. I drilled the base so the bolt heads sat flush with the bottom. There are dados for the vertical pieces. I wanted to make sure I could minimize any movement and I think this works with the triangle supports. By the way the dimension of 13” on the to...

Read this entry »


View Tom8021's profile

foot powered Scroll saw #6: Spring my foot

07-18-2009 05:48 PM by Tom8021 | 1 comment »

I bought a package of four springs at Home Depot. You can put a spring at the back or at the front. I tried the different sizes in different places and picked the 4” one near the front. I put it on by gluing short pieces of dowels, one to the base and the other to the bottom arm, and slipping it on. The next thing to do is drill a hole in the end of the bottom arm. I failed to mention that the hole for the blade holder is 1” in from the front end of both arms. Also, I cut ab...

Read this entry »


View Josh Hall's profile

St Giles Statement Piece

03-24-2013 07:28 PM by Josh Hall | 1 comment »

Here is the latest blog post for my St Giles project. there is a photo included. http://joshhallfurniture.weebly.com/1/post/2013/03/st-giles-statement-piece.html Thanks Josh

Read this entry »


« prev 1 ... 21 22 23 24 25 26 27 next »
265 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase