I was thinking whether or not to make this a continuation of the veneering bog, however many items here have more to do with vacuum systems, than veneering. Hence a new Blog! Photo one is a Demilune Hall Table top jig. Photo two is a 30 inch long tee square which we use for biscuiting and routing duties. We make marks on the blue tape, were the biscuits go. When were done we replace the tape. Photo three is an 8” square that we use to biscuit cabinet sides on. P...
Well, this is the last of this set of video episodes completing my first run at a veneering project. The panel turned out great and I am looking forward to exploring other wood species. This was a lot of fun. Trust me, if I can do this right out of the gates, anyone can! Thanks to Neil Lamens at Furnitology Productions and JoeWoodworker.com Finally the vacuum press is loaded! The vacuum quick connector attached to the vacuum bag Final 1/4 inch MDF hardboard panel veneered with Mov...
This episode covers glue-up of the “veneer package” leading to the final episode loading the vacuum press. Thanks again to Neil Lamens at Furnitology Productions and JoeWoodworker.com
This episode continues with making a platten for the veneer vacuum press leading into the next episode about glue-up. Thanks again to Neil Lamens at Furnitology Productions and JoeWoodworker.com
This episode completes the tape-up process for my first panel. More to come – I am trying to keep the clips short for easy uploading. Just a quick teaser . . . the panel turned out great. If I can do this anyone can! Thanks to Neil Lamens at Furnitology Productions and JoeWoodworker.com
Well, its going to be a long afternoon and evening as I am excited to “press on” and start my first veneering project. I am going to veneer a small panel as an experiment to see how the process works. I purchased a couple of veneer packs on sale at Rockler to use in my experiment. This first panel is 1/4 inch MDF hardboard veneered with movingui, a hard wood from Africa using TiteBond Cold Press Veneer Glue. Veneer – A thin surface layer, as of finely grained wood, glued to a base of...
My vacuum veneer press arrived from JoeWoodworker.com and I am excited to get it set up and start veneering. This episode goes reviews the press and the vacuum bag. Thanks to Neil Lamens at Furnitology Productions and JoeWoodworker.com
Well it’s been a weekend, not a lot of work done, but enough to make you think that you’ve accomplished something. Two screw-up’s, two corrections, one modification. Only had to recut two pieces of wood, not too major. Could have been a lot worse, and re-planed 6 boards that were too thick.I left off with the making of the lower case for the Buffet / Hutch. I stated that I needed to do some veneering and also some engineering for the mid drawer slides. I’ve done the veneering and done no ...
Below is my basic primer on veneering and the vacuum press. There is a lot of information available. This is the basic set that I have been studying. PRINT RESOURCES Purchased from JoeWoodworker.com From my FWW library – available online at FWW From my FWW library – available online at FFW From my FWW library – available online at FWW ONLINE RESOURCES Neil Lamens Furnitology Funitology Veneering Episodes: Episode 6 - Part 1 Episode 6 ...
VACUUM PRESS BAG STORAGE CONTAINERI recently was inspired to start veneering using the vacuum press by Neil Lamens at Furnitology Productions. If you haven’t had a chance to check out his website and video blog, it is really worthwhile to pay a visit sometime. He is currently finishing a contemporary veneered ash lingerie chest. I have been fascinated by this series. He has really focused on design elements and shop efficiency. His two episodes ( Episode 6 - Part 1 and Episode 6 - Part ...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 105 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 418 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- A Slice of Wood Workshop - 190 entries