Well here is my latest sled design. This sled is a combination of many sleds that i have seen in the past. One sled that really influenced it, is the super sled by john nixon at eagle lake woodworking. I like the t track on the sled part (the sheet part) but i am going to use real t track. I also liked the t track on top of the fence, which i incorporated, but it stops there. This sled should be able to do just about everything. You can cut 45’s ( blade tilting at 45 deg ) and every o...
Not far south of my ancestral homeland (one of them anyhow, as Americans tend to be from lots of places) on the French side of the English Channel – near the Blanchard Straights in fact, you’ll find Mont Saint Michel, a tidal penninsula on the Breton/Norman border. Constructed under, as well as commissioned by ancestors of mine (the Dukes of Normandy – future kings of England – and their forefathers, I feel a connection to the island, turned tidal penninsula, turned...
Going full time at working with your woodworking tools is quite a daunting task. It was, and still is for me. I get quite a few emails, visitors, and phone calls from other folks, so I know it is daunting for everyone that considers it. I try to be honest with them, about the cost and benefits. I have given out some bits and pieces of my “Pioneering Spirit” sermon over the past months to various individuals, but never all in one place before. So, I decided this morning to...
Well after going almost 2 months without doing a video and almost 2 weeks not being in the shop, I figured I would get some work done and while in the process shoot a short video. Well sadly my shop light burnt out and I have no bulbs for it, but I did get the video filmed before the light went out. Enjoy it and as always, all comments (good, bad, or terrible), tips, and tricks are welcome. Thanks!
Disclaimer: This blog follows my Magen David Board that is already finished and posted here This phase of the project took on a different pace. it was all hand tools oriented, and I was able to work on it at nights and at quick sessions as there was little setup involved, and not a whole lot of noise. To start. I took my old drill press table that was just hanging around the shop useless after I upgraded it and screwed a straight piece of cherry left over from my milling process to act ...
Over in the Forum, there is a question about Going Pro with woodworking, and what should be considered. The Forum Writer stated to “be honest.” I decided to post my comments there, and then also as a Blog Post. It will be easier for me to find my own comments later, and to document the thoughts as a Blog. Just a few misc., and random thoughts, as I don’t have much time this morning 1) Full time is so different than part-time, or hobby woodworking, that there isn’t any c...
Had a slight mishap today when I went to mill the legs down so they'd be the proper width after applying a "veneer" edge, I accidentally cut all the pieces! I should have left the those at the final width, I got a little carried away. A little creative thinking and milling a few more pieces out of the remaining door stock, and I'll have legs that will ultimately be a mere 3/16ths skinnier, but and I'm able to proceed using only this reclaimed door lumber. I've thought the inspiration ...
Found a link for sketch-up additions …. link... Haven’t tried any of them yet, I’m traveling etc , using my daughters pc, but couldn’t resit sharing.
I was able to squeeze another good day in the shop around work. I ran off to buy some more oak, then got home and planed enough of it down to glue up the stretchers/aprons for the table ends. While the laminations were cooking, I decided to give the BeadLock Pro a whirl. Having made integral tenons with chiseled mortises, and loose tenons with the router, I have to say this method is considerably easier and faster. First, I was able to cut off the parts to their finished length, without...
Hey guys! Taking advantage of the long weekend here in Canada, (so this was last weekend) I made a better base for my dremel. I was taking it apart to see why it was squeaking (trapped sawdust) when the idea hit me – drill the existing screw holes all the way through the body, and get a longer screw to hold the dremel together (like the old screws) and hold the dremel to the base. Well, I didn’t have a screw quite that long and thin, but I did have some short screws of the correct diameter. S...
- My Journey As A Scroll Saw Pattern Designer - 1584 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 96 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1609 entries
- frank - 417 entries
- degoose - 396 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 278 entries
- William - 258 entries
- Betsy - 221 entries
- shipwright - 213 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 198 entries
- Rustic - 188 entries
- BritBoxmaker - 185 entries
- Chris Davis - 183 entries
- Smitty_Cabinetshop - 176 entries